Chlorine is a sanitizer, and (unless you use Baquacil products) is necessary for maintaining a clear and healthy pool. Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly.
Are chlorine and shock the same thing? SKIMMER NOTES: No. Chlorine and shock are not the same thing. Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool.
Shocking will restore the proper chlorine level and restore water clarity. Both available in various forms: Chlorine comes in liquid, dissolvable granules, and granule pucks/tablets for slow-release. While shock is more fast-acting, it's also available in both granule (most common) and liquid forms.
Similarities Between Liquid Chlorine & Powdered Shock
Similarly, both forms have a higher concentration of available chlorine than those used in daily chlorination. They also both kill nearly all living microorganisms, bacteria and contaminants with ease.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
Low chlorine levels often cause green or hazy water, so if your water looks a little cloudy and you haven't shocked in a while, adding shock is the first step.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
Typically, you will not use regular chlorine tablets as pool shock chlorine. Calcium Hypochlorite: Also referred to as cal hypo, this chemical is one of the least costly and most convenient ways to shock your pool. It's usually sold in granular form. Needs to be dissolved before you add it to the pool.
Shocking is the process of adding chemicals (usually chlorine) to your pool to: break apart chloramines, also known as combined chlorine. quickly raise your chlorine level. kill algae, bacteria or other harmful pathogens.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool. As a reminder, you want your pH to be between 7.2 and 7.8ppm and your free available chlorine to be 1-4ppm for safe swimming.
So if you buy liquid shock, be aware that it only lasts one to two months at the most before it starts to lose effectiveness. While many swimming pool chemicals stay good for years if stored correctly, some pool-maintenance supplies expire more quickly.
Common unscented household bleach (sodium hypochlorite) works well to shock a pool.
2 ppm of Chlorine will take up to 4 and a half days or around 110 hours to evaporate from 10 gallons of standing water. Ultraviolet light, water circulation, and aeration will speed up the evaporation process dramatically. Chlorine will last between 6 and 8 minutes in 10 gallons of boiling tap water.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Raising pool chlorine can be much easier than trying to lower chlorine levels. Simply adding chlorine in the form of chlorine tablets, granular chlorine, liquid shock or powder shock will increase the total amount of chlorine within the pool.
Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. A proactive, productive and energy-saving maintenance activity is to remove the debris floating on the pool surface with a hand-held skimmer.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
Shock-chlorination is an essential and effective method of cleaning the pool. But you need to have the pump circulating the water for this to be effective.
Q. How long does it take to shock a pool? The actual process shouldn't take more than an hour, but depending on the product used, it could be up to 8 hours before you can use it.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
Chlorine has a low pH level, and in order to maintain your pool water's clarity and balance, shocking weekly will allow you to quickly raise the chlorine level, which will rid the pool of contaminants, without lowering the water's pH levels.
It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.