Grab a brush and some baking soda. Bicarbonate, the active ingredient in baking soda, is an effective spot treatment to help kill the algae and loosen it from the wall. Make sure you really get every last particle free; black algae has particularly long and stubborn roots which makes it a persistent strand.
Pool chemical measurements are based on 10,000 gallons of water. If your pool is larger or smaller, you'll need to adjust your math. A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool's pH tested below 7.2, add 3-4 pounds of baking soda.
Does baking soda kill algae in pools? Only algaecides can "kill" algae in pool water. However, baking soda can help clear up algae. Use both so you can restore sparkly, clean water!
Adding shock to your pool super-chlorinates your water. And this extra dose of sanitizer will kill algae growth. The more serious your pool algae problem, the more shock you'll need. We recommend using calcium hypochlorite shock, or cal-hypo shock, as an effective algae treatment.
There are hundreds of claims of homemade mixtures for killing algae, but baking soda is not one of the effective treatments you should try. Since baking soda is highly alkaline and reacts when mixed with an acid, many people assume it can be used to change the pH of a pond to discourage algae growth.
Chlorine is still one of the most effective killers of algae so doing a super-chlorination of 10-20 ppm of chlorine can go a long way towards wiping out the algae. Liquid chlorine is an ideal shock for algae because it is fast acting and does not add cyanuric acid (CYA) or calcium to the water.
Bleach is great for killing algae (and other organisms that may lurk in your tanks) and for keeping it from coming back.
Use a pool brush to vigorously scrub any pool surfaces covered in algae, including the walls, floors and steps. Apply a green algaecide according to the directions on the label. Let the water circulate for 24 hours, then brush the pool surfaces again. Vacuum or backwash to remove any remaining dead algae.
Shock Your Pool
Shocking is the process of adding chemicals to your pool to raise chlorine levels and kill bacteria and algae. We recommend using a calcium hypochlorite shock to treat your algae problems.
However, adding too much baking soda might also raise the PH level of your pool to an undesired stage (alkaline). In the case where too much baking soda is added to hard water, it can cause a build-up of calcium around your pool.
You will need to wait 6 hours to let the baking soda thoroughly dissolve into the pool water. However, you can often speed up the process by turning on the pool's circulation system.
You should wait at least six hours after adding baking soda before swimming in your pool. Even better, wait at least 24 hours to ensure it's fully mixed in and dissolved. While it's likely not harmful, if you get in the pool too early, the baking soda may irritate your skin or eyes if you're sensitive to it.
“Adding too much baking soda to a pool will cause the alkalinity to rise,” Vernon says. Anything above 120 ppm is too high. And over-alkaline water, he says, “can create scale build-up and cloudy water.” So as you add baking soda to adjust pH and alkalinity, remember to be patient.
Whenever pH drops below 7.2, add 3- 4 lbs. of ARM & HAMMER™ Baking Soda per 10,000 gallons of water to raise the pH. If after a day or so, the pH has not stabilized and drops below 7.2 again, add another 4 lbs. of ARM & HAMMER™ Baking Soda per 10,000 gallons of water.
Use baking soda as algae in pool home remedy
People like using baking soda to get rid of algae because you can swim immediately after treatment in most cases. Also, if it's not overused, it will only slightly impact pool water chemistry. It works best as a spot treatment for algae on pool walls and pool floors.
Most Algae Grows in High-pH Environments
Most types of algae typically enjoy higher pH levels, ranging from 8.2 to 8.7. Once algae starts growing, it can further raise the pH level in your pool and cause more algae growth.
Nannini's test suggests that the Magic Eraser works to an extent, but is not a cure-all. “I'd say it's just collecting the algae, but it's definitely not correcting any water balance,” she said.
All species of algae are one of three colors: green, yellow or black. Shocking the pool with chlorine is one way to kill off algae growth and make the pool safe and clean again.
Mix two gallons of water, two cups of oxygen bleach, and one cup of borax. Stir the recipe until everything dissolves. Add ¼ cup of dish soap and stir. Apply the cleaning solution and scrub with a brush.
You could have inadequate filtration for your pool's size or low or inconsistent chlorine levels. Bad water circulation with dead spots or pool imbalance in your pool chemicals are also two big culprits. One or any of these factors can kick off a pool algae bloom that spreads across your pool.
Pool algae can be caused by poor filtration, out-of-balance water, low or inconsistent chlorine levels, or poor water circulation. Green, dark green, yellowish green and blue-green algae are the most common. Green algae are slimy and are the leading cause of green pool water.
Algae can persist in a pool even after shocking. A green pool – especially one that turned green overnight or after rain, can also be from a pool pump that isn't properly circulating water or an issue with your filtering system.
Hardware stores and home centers sell products designed to kill moss and algae, but you can save money by using inexpensive chlorine bleach or a non-creamy hand dishwashing detergent, such as Dawn.