Whether your patio is sealed concrete or cement, or even sealed concrete pavers, a bleach and water solution makes it easy to clean away built up soil, stains from leaves and pollen, mold, mildew and algae.
Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
Mild detergent and water.
Mix some mild dish soap with water in a bucket to create suds, then use a brush or a sponge to scrub the surface of the pavers. If your pavers are textured or have intricate designs, this cleaning method can be gentler than a power washer.
Cleaning pavers with bicarbonate soda and vinegar
Fill the bucket with lukewarm water and then add the bicarbonate soda, making sure it dissolves properly. Then add a little bit of white vinegar. Pour the solution onto the stained areas on your paver surface and use the scrubbing brush to apply it thoroughly.
Use Vinegar or Bleach
If you are going to try this approach to remove mold or algae, first try a mixture of white vinegar and water to spray down the area and kill the mold.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
OxiClean is a powerful concrete cleaner that works well on various materials, including pavement and grout. This concentrated solution provides excellent cleaning without leaving residue.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
The pressure washer in combination with a dirt cutter is an excellent option. This removes not only weeds and moss from the surface, but also from indentations. Keeping up with this type of cleaning means that there is less time for weeds to grow. It also helps to maintain the beauty of the paving stones' surface.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Baking soda has low-abrasive properties, making it an excellent cleaning material for stuck-on grime and tough stains. Additionally, baking soda is absorbent, allowing it to absorb oils from the surface of the pavers, especially freshly oil spill on concrete pavers.
Acidic cleaners: Harsh, acid-based cleaning products and stain removers can damage the seal and finish of your concrete pavers. Bleach: This alkaline solution may be effective for other household uses, but it can discolor concrete pavers that have been colored or stained.
Scrubbing With Bleach
If you have stubborn stains on your brick but don't have a power washer, you can try scrubbing. Simply mix a 10% solution of chlorine bleach to water in a bucket. Scrub the area with a stiff-bristle brush. Once you remove the stains, rinse the brick thoroughly with clean water.
Use Bleach
But that's not all; chlorine bleach can also be used for cleaning the concrete driveway. Of course, you should dilute it with equal parts of water or a 1:1 ratio. With the mixture ready, spray it on the driveway, allowing it to sit for 10 minutes. Then, use a stiff brush before rinsing with clean water.
Yes, you can pressure wash your pavers. But while using a pressure washer at a basic level is simple, ignorant and inexperienced users can easily damage their pavers by using a stream that's too powerful, by holding the wand too close to the pavers, or by falling into any number of other rookie mistakes.
You can use a pressure washer on your patio pavers if you want to clean stubborn stains or mildew from them. However, be very careful when doing this! Use a gentle spray and avoid letting the water run down the sides of your pavers, especially if they're set in the sand rather than mortar.
Simple Green is one of the best cleaning products for dirty pavers. It doesn't have any harmful chemicals that could possibly warp your precious driveway. Less chemicals mean there's a less likely chance your paver stones will change to a weird-looking color.
Although bleach is great at the whitening effect, you can use peroxide to achieve this. Hydrogen peroxide is an oxygenated bleach. It is safe for plants, so when you rinse this solution, it won't harm anything. It works together with the dish soap and baking soda to remove dirt and whiten dirty concrete.
Try Concrete Stain
The simplest path to reviving tired pavers is to apply an acrylic-based semitransparent concrete stain, such as Behr Premium Semi-transparent Concrete Stain ($27/gal.; Home Depot) or Valspar Semi-transparent Concrete Stain ($28/gal.; Lowe's).
A dish soap, like Dawn, is a safe place to start. The surfactants in dish soaps are designed to remove oil and grease, they're gentle enough to be used without issue on your pavers. In a bowl or bucket, mix the soap with water and pour it onto the stain and agitate. Rinse and repeat if needed.
Regular Soap and Water
A solution of regular dishwashing soap or hand soap is simple to create, and it will remove mild to moderate dirt, stains, and grease. Just mix your soap and some warm water in a large bucket and you're ready to start cleaning.
Depending on the material of the paver (non-coloured concrete is safe), CLR may be suitable. Always spot test in an inconspicuous area first. Make sure the pavers are not coloured, stamped, sealed or coated.