What happens when you add too much clarifier is that all the little particles clump together too much an end up as a colloidal suspension. When that happens, the whole thing turns cloudy. It'll clear but it will take a while. Run the filter 24/7 until is clears.
You will likely end up with cloudier water if you add too much clarifier. You've been warned! To add the correct amount you'll need to know your pool water volume.
Yes, you can put too much clarifier in the pool, and about the only way to get rid of it is to filter it out or drain & refill alternately. You'll need to watch your filter pressure and also check your filter media to see if it needs to be replaced as too much clarifier can gum up your sand or DE.
During the swimming season, the pump and filtration system need to run for at least 8 hours every day to properly clean and filter the pool water. If it's only on for a few hours daily, then the system won't have time to clean the pool, leaving the water cloudy.
Pool flocculant can clear up your cloudy pool water in 1 or 2 days. Though it works faster than pool clarifiers, it will need 8 to 16 hours to clump together the particles before you can vacuum. Add flocculant to your pool with your filter on “recirculate.” Then let the flocculant sit overnight with your pool pump off.
Clarifier works to clear mild cloudy pool water. Add it every other day as your filter runs until your water clears. If you have extremely cloudy water, you need to use a pool flocculant.
To maintain a clear sparkling pool add 4 fluid ounces of Water Clarifier per 10,000 gallons of water weekly. If the pool is cloudy due to dust or to high hardness of the water, add 32 fluid ounces of Water Clarifier per 10,000 gallons of pool water.
For the most part, yes. It can be unattractive and it should be addressed, but it is mostly safe to swim in cloudy water. The only exception would be if the pool is cloudy because there are too many chemicals in it. This pool water would be unsafe to swim in and should be avoided.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals.
If your pool is just mildly cloudy and you are not in a rush to clean it out, a clarifier may be your best bet. A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
Maintain proper water balance and chlorine levels following treatment. Some clarifiers may increase pool pH levels.
Works with all filter types & will not clog filters. Reduces sanitizer (chlorine) demand by removing dirt particles.
Answer: Try using chlorine bleach (liquid chlorine) instead of granulated chlorine; this will clear and help keep away algae from your pool. Free chlorine should always be at 3ppm to avoid algae and cloudy water.
Adding a recommended dose of shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
In most cases, a cloudy pool after shocking is only temporary and should clear up within 24 hours. Keep filtering your pool, add a little clarifier to help, and your pool should be clear in no time. If after 24 hours your pool is not clear, then you may need to look a little deeper for the solution.
GETTING RID OF ALGAE
Please note that our liquid algaecides are compatible with alkalizing and flocculating agents used in other pool maintenance products. Our Liquid Algaecides are patented formulas that not only work as preventatives but as a pool clarifiers that inhibit algae growth of all types.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
It says to shock it once a week. And 4. Add algae gaurd 60 every 3-5 days to prevent algae. Also add clarifier 4-12 hrs after above steps, once a week to help get rid of algae and organic debris.
Foaming in a pool means there are high levels of total dissolved solids (TDS) in the water. TDS are the measure of solid matter that has liquefied. Foreign solids like oil, soil, and dirt dissolve in pools. High levels of TDS makes pool water look cloudy and can even make it taste salty.
Of course, too much chlorine in pool water can be dangerous. Exposure to over-chlorination can provoke asthma, lung irritation, and potentially skin and eye irritation. As well as being potentially bad for you, it's bad for your pool.
1) After shock - Sometimes pool water looks cloudy right after you apply shock granules such as cal-hypo, or liquid shock, but rest assured it's only temporary. This could be due to change in water balance – meaning your pool water temporarily goes off balance when adding these products.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.