Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter's pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.
Open the air bleeder assembly on your filter and turn pump on. Watch the pressure gauge for spikes. After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear.
Turn on the pump and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear. Turn Off the Pump. Set the filter valve handle to the RINSE position and ensure the handle locks in place.
When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.
Whenever the filter fills up with the dirt/debris it reduces the flow of water to your pool. Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
Set the valve to Rinse. Depress the valve selector handle, then turn it to the Rinse setting. After a backwash, sand and debris becomes unsettled settle in the filter's internal plumbing. The rinse setting returns to the normal path through the filter, flushing debris to waste.
On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day. But here's the thing: you don't have to run your pool pump consecutively. You can choose to run it for three hours in the morning before you leave for work and another 5 hours in the evening.
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value's waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
Normal pressure for most pools is between 10 and 25 PSI (70-170 kPa). The pressure for filtration systems varies depending on the type of filter, the size of the lines, the pump and other pool equipment.
High swimming pool filter pressure is usually the result of a lot of particles being filtered out of the swimming pool water. When pressure rises it is time to backwash the filter if you have that option with a sand or diatomacesous earth (DE) filter.
It could be a clogged pump basket, impeller, pipe, or skimmer basket. It could also be a closed or broken valve before the pump. In some cases, the pump may have an air leak and is drawing in more air than water. This can reduce filter pressure (and filtration ability).
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
After a backwash, to get the amount of DE powder, simply take the recommended amount of DE powder for a new filter and multiply it by 0.8, or 80%.
It is not recommended to drain a swimming pool through the backwash valve. While sucking from the main drain and putting the water down the backwash line will work in some scenarios it puts your pool pump at risk of losing prime and running dry.
The 'Rinse' setting should be used after backwashing and again run just for a minute or two. On this setting the water is flowing through the filter in the normal direction but once again is being sent to the waste pipe rather than being returned to the pool.