Heavy shocking with granular chlorine will generally require 24-48 hours before the chlorine level has dropped to safe swimming levels (below 5 ppm). Lithium and Non-Chlorine shock labels typically allow immediate swimming, but check the package label, to be sure.
Keep your pump and filter running. Give the shock a good 12 to 24 hours to work it's magic. If the algae hasn't cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.
Shock the pool with either the liquid or granulated chlorine shocks. Let the filter run for 24 hours before adding any other chemicals. You should see a noticeable difference the next day in the water clarity.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
Needs to be dissolved before you add it to the pool. Must be used after dusk. Allow eight hours to pass after shocking before you can safely swim. Adds about 0.8 ppm of calcium to your water for every ppm of FC added.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
Add Pool Water Clarifier
After your pool water has circulated and your shock has dissipated, it's time to add your clarifier. Clarifier helps bind tiny particles into bigger particles that your filter can capture.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Although vacuuming should be combined with pool shocking, it's better to vacuum the pool before you shock the water. A good scrubbing and vacuuming of the pool walls and floor will ensure that dirt and debris that can affect the water chemistry is removed before the chlorine is added.
Best Time to Shock Your Pool
The best time of day to shock pool is when the sun is down. So, experts recommend shocking your pool in the evening or at night, to make sure it does its job. Shocking during the day can be ineffective as UV rays from direct sunlight significantly reduce free chlorine levels.
Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool. Short answer: No. Chlorine sanitizers and shock are similar but different in strength.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Adding a recommended dose of shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
Never close the cover immediately after shocking the pool. It is recommended to wait several hours before closing the cover. Use a test kit to regularly test the pool water. If the tests results are good, this does not imply the water chemistry was good prior to your current test results.
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.
Run the filtration system
While shocking your pool will help kill any germs any algae, it won't actually get rid of them; for that, you need your filter. So be sure to run your pool filter for at least 24 hours.
Heavy shocking with granular chlorine will generally require 24-48 hours before the chlorine level has dropped to safe swimming levels (below 5 ppm). Lithium and Non-Chlorine shock labels typically allow immediate swimming, but check the package label, to be sure.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.