Using a small screwdriver, gently turn the calibration screw or move the adjustment lever until the thermostat's temperature reading matches the thermometer's reading. Make minor adjustments and allow time for the thermostat to adjust to the new setting before rechecking the temperature.
If your thermostat is not reading correctly, it might be due to a dirty or faulty sensor. A quick fix could be to gently clean the sensor with canned air to remove any dust buildup. However, if problems persist, replacing the thermostat could be the next step.
To do so, locate your home's thermostat and tape an accurate thermometer on the wall next to it. Wait 15 minutes and check the temperature reading on both devices. If your readings are three or fewer degrees apart, you should be good to go.
Dirty or worn flame sensors, blower motor problems, clogs in the condensate lines, and electrical issues are some of the many problems that can leave your HVAC system failing to deliver the temperatures you've programmed in your thermostat.
Use the manual to find the screw for calibration. Turn the screw to match the temperature of the thermostat to the room temperature. Turn the HVAC system and the power back on, and the power. Turn on the thermostat and wait a few minutes for it to adjust to the temperature.
Leave both units in place for another 20 minutes, and check the readings again to see if the readings are the same. If the readings between your thermostat and thermometer are still different, you likely have a malfunctioning thermostat and there may be an issue impacting thermostat accuracy and efficiency.
If the temperature is set to 74°F but the thermometer shows 78°F, you will have to recalibrate the thermostat to account for this 4-degree deviation. Even with older AC units or furnaces, you might have to recalibrate your thermostat from time to time.
If your thermostat is not reading correctly, it might be due to a dirty or faulty sensor. A quick fix could be to gently clean the sensor with canned air to remove any dust buildup. However, if problems persist, replacing the thermostat could be the next step.
Another problem that can cause your house to be hotter than what you've set the thermostat to is if your home's HVAC system isn't sized properly. An HVAC system that's too large for your house will cool your home unevenly. It will only cool some rooms off and then shut off versus cooling down the entire house.
Thermostats can lose calibration over time from being accidentally bumped or from dirt accumulating. An improperly calibrated thermostat can cause discomfort because it's not heating your home accurately.
Clean the Thermostat. Sometimes, when the room temperature doesn't match the thermostat setting, the problem could be dirt buildup on its interior parts. A dirt coating around the inner components may create excess heat and cause the thermostat to give the wrong readings.
If you're cold even though your thermostat indicates you shouldn't be, your furnace likely isn't the problem. In most cases, it's working just fine. It's your home that needs attention. Lack of insulation, severe air leakage, and/or unbalanced ductwork are frequently to blame.
After taping the thermometer to the wall, wait for 20 to 30 minutes and then check both the thermometer and the thermostat to see what the temperature reading is on each. Ideally, both will show the same temperature, but a small difference between the two is also fine.
A dysfunctional fan can be why your thermostat won't change temperature. This problem prevents the furnace system from forcing heated air into your home. Solution: switch off the furnace, wait two minutes, then switch off the fan.
The calibration screw is typically located in a curved piece of metal. First, remove the control unit from the wall mounting and then locate the screw in the back. Turning it back and forth opens the contacts. Once you feel the setting is correct, turn the calibration screw again to close the contacts.
A dirty thermostat sensor will send the wrong readings to your heat pump or furnace. This can lead to that imbalance between the numbers the thermostat is showing and how you feel inside your home. Thankfully, this is an easy fix. You only need to clean the thermostat.
Cleaning the inside of your thermostat may fix the issue. If there is too much dust inside, the sensor will have trouble working correctly. After cleaning, if you're still having problems, you may want to recalibrate your sensor.
For many of us, 70 degrees is the ideal indoor temperature, but when it is close to 100 degrees outside, your AC unit will be working quite hard to meet these expectations. Consider setting your thermostat at 75 degrees to 80 degrees in your home if the outside temperature is approaching triple digits.
Cooling a house from 80 to 72 degrees is a common goal for many, especially during the peak of summer. On average, this process takes roughly two and a half to three and a half hours.
When you set the thermostat above or below the current room temperature, you should hear a click, and the AC or furnace should kick on almost immediately. If you make changes at the thermostat and nothing happens, that's the first sign you have a bad thermostat.
Locating the Reset Button
Remove the thermostat cover by either snapping it off or unscrewing it, depending on the model. Most modern thermostats will have a clearly marked reset button inside the panel. It's usually small and recessed, so you might need a pointed object like a paperclip to press it.
If your thermostat is set to a temperature regulation mode or has an energy-saving program enabled, it might reset to conserve energy.