The leading cause of bearing failure is improper lubrication, which accounts for the vast majority of all bearing deaths. However, bearings operate under extreme stress and can be destroyed by five primary factors:
NO. WD40 is a degreaser - not a grease!! The object of cleaning your bearings is to remove all the grease, clean the bearings, then add grase back in. Spraying WD40 will remove the old grease, but it won't clean your bearings, and it won't regrase them afterwards.
13 Most Common Reasons Why Bearings Fail
Many people use acetone when cleaning skateboard bearings as it can be found in nail polish remover, or they may use a rubbing alcohol over 90%. For this example we are using the Loctite 7061 Super Clean. It's a reliable brand that we trust, and know it will do the job perfectly.
Can You Clean Bearings With Vinegar? Technically yes, although it is recommended to use Acetone or some kind of rubbing alcohol as they leave no trace or film on the bearings. Vinegar or citrus-based cleaners can leave a thin trace on the bearings which can give dust a place to settle.
I do not recommend the alcohol methods or the hydrogen peroxide. I'm not a fan of lighter fluid, but it works great. There's this electrical contact cleaner spray that supposedly works good but in my experience it's not all that great.
Hydrogen peroxide is no longer recommended for cleaning cuts, scrapes, and open wounds. While it kills bacteria, it is not specific and also destroys healthy skin cells and tissue essential for healing. Additionally, it should not be used for acne, as it can dry out and irritate the skin.
Yes, you can clean bearings (such as those for skateboards, roller skates, or fidget spinners) with isopropyl alcohol. It is a highly recommended solvent because it effectively breaks down old grease, removes grime, and dries without leaving a residue.
Traditionally light oil, kerosene or degreaser based on Isopropyl alcohol are recommended as the cleaning agent. However, the industry practice has been to provide commonly available diesel, mineral turpentine oil (MTO) and kerosene as the cleaning agent to its Maintenance team.
No, they are different chemicals. While both evaporate quickly and dissolve grime, 100% acetone is a harsh solvent used for paint stripping and artificial nail removal. Rubbing alcohol is a milder antiseptic generally made of isopropyl alcohol and water, used for disinfecting and cleaning.
Bearing failure can occur for myriad reasons. The most common examples, however, are as follows: Improper lubrication. Most failures happen as a result of improper bearing lubrication.
A wiped bearing surface is where surface rubbing, melting and smearing is evident. This may be due to a variety of causes, including: Excessive load at start-up/run-down. Insufficient lubricant. Operational overload.
Bearings typically last between 85,000 and 150,000 miles. However, their exact lifespan depends heavily on the type of machinery, operating conditions, and maintenance.
What Should You Avoid When Cleaning Bearings?
Just as WD-40 can damage rubber, it can also damage plastic, so when your drawers and cabinets have plastic components, avoid using WD-40 to solve lubrication issues.
The right lubricant for your bearings depends on the application, but generally, use heavy-duty grease for high-load, slower-moving parts (like car wheels or mower decks), and lightweight synthetic oil for high-speed, low-load parts (like skateboards, fishing reels, and RC motors).
Acetone is a highly effective, fast-drying solvent for cleaning skateboard, roller skate, or yoyo bearings because it quickly dissolves old grease and grime without leaving a residue. However, it is highly flammable and can melt plastic parts, so it must be used safely in a well-ventilated area.
No, you shouldn't. You aren't getting a straight answer because you shouldn't use anything. The bearings are already packed with the correct grease and sealed, the only maintenance is replacing them when they need it, maybe 3-5K miles. You don't grease car bearings either, just replace them when necessary.
Products we DO NOT recommend are petroleum-based products like; paint thinner, gasoline, kerosene, lacquer thinner, turpentine or anything that contains tolulene. These solvents aren't adequate cleaners and should not be used in the bearing cleaning unit.
The best bearing cleaners depend on your setup, but the ultimate industry standard is a dedicated unit like the Bones Bearings Cleaning Unit paired with a heavy-duty solvent like pure acetone or 95% isopropyl alcohol. For a fast, all-in-one approach, electric or mechanical scrubbers and citrus-based washes are top-tier choices.
The best acetone substitute depends on your specific cleaning task. For heavy-duty degreasing and adhesive removal, use mineral spirits. For general electronics, surfaces, and light grime, choose isopropyl (rubbing) alcohol. For plastics or delicate surfaces, use mild citrus-based cleaners or pure soap and hot water.
Soak Bearings in Cleaner
Acetone, isopropyl alcohol, and mineral spirits are all good options for this task. However, it's important to wear gloves and avoid contact with your skin when using these solvents. To begin, you will need a dish or wide-mouthed bottle to act as a container for soaking the bearings.
Hydrogen peroxide is often used on its own for spot treatments, but pairing it with dish soap expands its usefulness by allowing it to tackle oily residue at the same time. That balance is what makes the mixture feel more powerful than many single-purpose cleaners.
Hydrogen peroxide reacts violently—and sometimes explosively—with catalytic metals, strong reducing agents, combustible materials, and organic solvents. The violence of the reaction depends heavily on the concentration of the hydrogen peroxide.
Hydrogen peroxide is no longer recommended for everyday wound care because it does more harm than good. While it kills germs and causes that familiar fizzing, it is indiscriminate—destroying the healthy skin and immune cells your body needs to repair the tissue.