Concrete pads are excellent to use as a base for your above ground pool, but you'll want to add another cushion between the two. Concrete is an abrasive material and will wear on the liner if it's in direct contact. Concrete is the best choice for a solid base because it is perfectly flat.
Sand is the recommended base material upon which an aboveground pool should sit. Sand is used under an aboveground pool to protect the pool's vinyl liner from rocks and objects that could tear the liner. Also, sand under an aboveground pool acts as cushioning for its floor, making it more comfortable for feet.
Using gravel or rock is one of the most popular ways when landscaping around your above ground pool. These rocks are readily available and suitable for all climates. They range in sizes, shapes and colors so you can always find the style you need to compliment the rest of your yard.
Should I put a tarp under my Intex pool? At the bare minimum, yes you should put a tarp underneath your Intex pool. Inflatable pools, Bestway and Summer Ways pools will also benefit from a tarp.
Do not attempt to install an above-ground pool below ground where all sides of the pool are surrounded by dirt. The weight of the soil when it becomes saturated with water will cause the walls to collapse. Professional excavation is recommended if more than a few inches of slope must be removed for the pool to fit.
The use of sand is one of the cheapest ways in which to level the ground without digging, and it is far easier to level the sand than it is to level the ground itself. Sand can be poured on the installation area, spread evenly around the region, and compacted down to create level ground.
There is an easy way to do this. Screw two 2-by-4 boards together alongside each other so they are one or two feet longer than the diameter of your pool. Next, lay the attached boards on the ground where the pool will be and put a level on top. Slowly lift and lower one side of the 2-by-4s until it shows level.
For a rectangular pool that's 18 feet long by 9 feet wide, you'd need at least 1 cubic yard of sand for your base.
The general rule is that there should be a two to three-inch base of sand under an above ground pool. If you know the dimensions of your pool area, then you can easily figure out how much sand you'll need for the base using a sand calculator.
Chlorine/non-chlorine chemicals – When adding chlorine or non-chlorine chemicals to “shock” your pool after a fill-up, wait about 24 hours or until levels are approximately 5 ppm. If you'll only be adding liquid chlorine, it's generally safe to swim after about 4 hours or until levels are 5 ppm or lower.
Underneath the liner is a sand or cementitious floor, troweled into place. The floor sidewalls come up to meet the walls, which are commonly 42” x 8 ft panels made of galvanized steel or thermoplastic. These walls are supported from behind so that they won't bow out against the weight of the water.
Many wonder though if above ground pools are exclusively used over grass, sand, or soil only and if installing it over concrete is impossible (for fear of it getting punctured). The good news is, yes, you can install your above ground pool on concrete if a sand or soil base is not possible.
Gorilla Pads are pre-cut floor pads designed to protect and cushion the bottom of above ground pools. Unlike old pool foam padding, which can be easily be cut or pierced by grass, roots, or rocks under your above ground pool liner, Gorilla Bottom pool floor padding is impervious to almost any sharp object.
The ground must be compact and firm, so the pool should not be set up on mud, sand, or loose soil. To level your inflatable intex pool, you may put blocks on the ground to have a level intex pool. The other options for leveling the pool area are a 2 x 4 with a carpenters level or a water.
To set up your Intex pool on uneven ground, Start by outlining your pool on the floor. Use a stake and place it at the center of the place then tie a string to it. Measure the string to the radius of the pool and add 1 foot to the measurement.
Mason sand, sometimes called mortar sand, can normally be found at any sand/gravel yard or masonry supply yard. It is usually measured in yards. It is very fine and should not contain any rocks or pebbles. This will create a very smooth bottom and is the most popular method to use when installing an above ground pool.
Yes, every above ground pool needs pool cove. Pool cove is simply a berm or wedge that transitions the pool floor to the pool wall.
Though less commonly used than yellow mason sand, it's also possible to find white sand in use as a base material for pavers, or in swimming pools.
And for this reason, many people ask, “Can above ground pools be partially buried?” in hopes of receiving the best of both worlds. The short answer is that “Yes, they can!” However, there are some things that should be taken into account if you're going to go down this route.
Filling your pool with dirt is the fastest and most affordable way to get rid of a pool because there's no need to remove your concrete or metal shell. This saves on both labor and hauling costs. However, filling a pool with dirt is still a delicate process that requires careful preparation, drainage, and demolition.
Backfilling can be done with sand, dirt, or gravel. Consider the goals of the project and the budget when choosing a fill material. The backfill materials we normally use at Superior Groundcover are class 2 fill sand and pea stone. Pea stone is the best fill material because it's self-compacting.