A quick and easy way to increase water pressure is to adjust the pressure-reducing valve, which can be found in your home, usually close to your water meter. If your pressure gauge reading was low, make slight adjustments to your regulator.
A quick and easy way to increase water pressure (for homes supplied by a municipal water system) is to adjust the pressure-reducing valve, which can be found on the main water-supply pipe; look for a conical-shaped valve next to the water meter, close to where the main water pipe enters the house.
Anything exceeding the normal range (60, 70, or even 80 PSI) can cause significant problems with your home plumbing system, making it more susceptible to leaks, water hammering, pipe bursts, and problems with your fixtures.
The short answer is low water pressure in your home arises due to a number of causes. Some include a shut or blocked water meter valve, mineral buildup clogs pipes, corroded pipes, or even a crack in the main city supply pipe to your home.
Most residential plumbing systems are designed to handle 40 to 60 PSI of pressure, with 80 PSI being the typical maximum and anything over 100 PSI being possibly detrimental to plumbing components.
Water pressure is measured in psi, or pounds per square inch, and represents the force at which water enters your home from the water main. Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80.
If the pressure of the water entering your house is 100 psi or above, it can damage the plumbing. The pressure will cause dripping faucets and leaks in the pipes. It's also harmful to water-using appliances, such as water heaters, dishwashers, and laundry machines.
Open your main water valve.
Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure. Sometimes the main valve is turned off accidentally during routine repairs and maintenance without the homeowner's knowledge.
A fast drop in only one faucet means there's a problem with the faucet. Rapid low pressure affecting one area of the house may mean a corroded pipe issue. An abrupt water pressure drop affecting the whole house may mean a water main break (municipal water) or a well pump problem (well water).
(Normal is 60 psi and very few areas are below 40 psi) The pressure of the streams will drop under these extreme conditions, of course, but the stream integrity is preserved. This photo shows the stream integrity of our Perfect shower head (old style).
Normal water pressure range
In general, residential water pressure ranges between 45-80 psi (pounds per square inch). If your water pressure is under 40 psi, it's considered low.
Residential water pressure tends to range between 45 and 80 psi (pounds per square inch). Anything below 40 psi is considered low and anything below 30 psi is considered too low; the minimum pressure required by most codes is 20 psi. Pressures above 80 psi are too high.
Water has the unfortunate quality of being heavier than air. In fact, it weighs 62.4 pounds per cubic foot. This mass requires a pressure of 0.433 psi to lift water one foot (62.4 lbs/144 in in ft). To put it another way, one psi will lift water 2.31 feet (1/0.433).
If the pressure is 35-60psi, that is enough pressure and flow to allow most plumbing fixtures to work properly, unless there is a restriction within the system obstructing the flow from what it should be.
The relationship between PSI and feet of head is that 2.31 feet of head = 1 PSI. Translated, that means that a column of water that's 1-inch square and 2.31 feet tall will weigh 1 pound. Or, one-foot column of water that's 1-inch square weighs .
Pressures above 80 psi are too high. Whereas low water pressure is more of a nuisance than a serious problem (some fixtures, like washing machines, have minimum pressure requirements), high water pressure carries with it a significantly increased risk of damage to pipes, joints, fixtures and seals.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
The ideal water pressure for a house will be somewhere in the range of about 45 to 65 psi. Anything higher than 80 psi can cause damage, and anything much lower than 45 psi may result in issues when you use your shower, toilet, dishwasher and other water-consuming appliances.
The water pressure at the site of the Titanic wreck is roughly 6,000 psi (more than 41,000 kilopascals). Under this amount of pressure, even the slightest structural flaw could result in fatal consequences. Death would be virtually instantaneous for the occupants of the pressurised chamber.
To test your home's water pressure, you'll only need a simple, low-cost pressure gauge, which you can get at any hardware or home improvement store. Look for one that has female hose threads for a simple connection, a rubber gasket for a tight seal, and the power to measure up to 300 pounds per square inch.
As you descend, water pressure increases, and the volume of air in your body decreases. This can cause problems such as sinus pain or a ruptured eardrum. As you ascend, water pressure decreases, and the air in your lungs expands. This can make the air sacs in your lungs rupture and make it hard for you to breathe.