Answer: The best thing to do is to take the reading for free chlorine first; then you can use pool calculator to find the amount of chlorine to add. Your free chlorine should always read 3 ppm. A 1000 gallon pool may just need 0.13 ounces or a little higher.
If the water is clean and clear, then add about 3 oz of liquid chlorine per 1000 gallons of water – while the pool filter is running. This should give you a chlorine level of about 3 ppm.
How much shock do I need to shock my pool? A simple ratio and a standard rule of thumb to follow when you shock your pool is to dissolve one pound of either calcium hypochlorite or sodium dichlor for every 10,000 gallons of pool water.
Often, it will look something like this. 12.5% Liquid Chlorine Pool Shock – Normal Dosage: 1 gallon of shock per 10,000 gallons of water. Shock Dosage: 2 gallons of shock per 10,000 gallons of water.
Generally speaking, the dosage amount of pool shock is 1 lb. per 10,000 gallons, but consult the shock package label.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
For laundry bleaches: 1 gallon is required for every 1000 gallons of water, and there are 1500 gallons of water in the well. Therefore, 1 ½ gallons of laundry bleach is required to disinfect this well.
If your pool is larger or smaller, you'll need to adjust your math. A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool's pH tested below 7.2, add 3-4 pounds of baking soda.
One pound of shock treats up to 10,000 gallons of pool water. Also, keep the pool filter and pump running for at least 10 hours during and after you shock.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
1) After shock - Sometimes pool water looks cloudy right after you apply shock granules such as cal-hypo, or liquid shock, but rest assured it's only temporary. This could be due to change in water balance – meaning your pool water temporarily goes off balance when adding these products.
Liquid chlorine and granular shock have the same active chemical that sanitizes your pool, what changes is the strength and the way you use it. Liquid chlorine is less costly, unstabilized and comes in liquid form. Granular shock is stabilized and comes in a solid form that dissolves in your pool.
To dose water in a tank with 5 mg/L chlorine use: 40 millilitres of liquid pool chlorine or 170 millilitres of bleach, for every 1000 litres in the tank.
Use 1-3 tablets at a time, depending on your pool size. You'll need enough to establish and maintain proper chlorine levels. Small Intex pools under 12′ in diameter should use 2-4 of the 1″ tablets in a chlorine floater. In addition to everyday chlorination of your Intex pool, you may have heard of shocking the pool.
Common unscented household bleach (sodium hypochlorite) works well to shock a pool.
What can you use instead? Bromine — considered a safe substitute for chlorine. Looks for BCDMH tablets, which are typically 66% bromine and 27% chlorine. If unable to find, you can use just bromine but it may leave the water a dull green color.
Calculate the amount of bleach you need based on the fact that 1 gallon will raise the free chlorine level of 30,000 gallons of water by 2 ppm. If you need to mildly shock a 30,000-gallon pool by raising the free chlorine concentration to 5 ppm, you need 2.5 gallons of bleach. To raise it to 10 ppm, you need 5 gallons.
Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine. Household bleaches often have unwanted fragrances and colors.
If you need to calculate how much bleach or Clorox you need to shock your pool, you will have to use 1/2 gallon of bleach per 10,000 gallons of water to raise the chlorine levels by 5 ppm.
Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water.
So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.
It's recommended that you should do a pool shock once a week. The more you use the pool, the more often you need to shock it. Occasionally, you may need to perform an extra pool shock after: Heavy pool use, like a pool party.