Most floating chlorinators can hold anywhere from two to eight weeks worth of chlorine, depending on conditions such as the season and your pool's size. An automatic feeder works in a similar way, allowing it to mix with the pool water slowly and deliberately. This type generally comes in a large bucket.
All pool chemicals, aside from unstabilised liquid chlorine, are good for up to three to five years as long as they're stored in a cool and dark place away from sunlight and they're packed in air-tight containers. Granular chlorine can be re-packed to extend its shelf life.
Remove Chlorine by Evaporation
The surrounding environment dictates how long it takes for the chlorine to evaporate. Warmer air will cause the chlorine to evaporate more rapidly. If you decide to place the water in a jug that's left open in the refrigerator, the chlorine should evaporate completely within 24 hours.
The degradation rate of chlorine in direct sunlight without CYA is 75 % loss in 2 hours or a complete loss of chlorine in 4 hours. CYA will keep the chlorine in the water 8 times longer than without it. CYA slows down the chlorine kill rate so more chlorine is needed for safe water.
Shock is liquid or granular chlorine. You should add one gallon (or one pound) of shock per 10,000 gallons of pool water every week to two weeks. During hot weather or frequent use, you may need to shock more frequently.
Aim to maintain a chlorine level of 3 to 5mg/l at all times. How frequently you add more chlorine will depend on your usage and bathing habits. It could be daily, every two to three days or weekly. For 1mg/l, add 2g per 1000 litres.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
You might have an infestation of algae, fungus or bacteria that can deplete normal chlorine levels and it is possible for this to occur without many visible signs. Your pool may appear to have a dusty look on the pool bottom. If you brush it and it clouds the water, then it is most likely a Mustard Algae.
One of the causes of a high chlorine demand is an excessive buildup of algae and phosphates. Although you're adding chlorine to your water, bacteria or algae are overpowering the chemicals causing it not to show up on tests strips or in water kits.
Yes, boiling water for 15 minutes is one way to release all the chlorine from tap water. At room temperature, chlorine gas weighs less than air and will naturally evaporate off without boiling. Heating up water to a boil will speed up the chlorine removal process.
Two forms of vitamin C, ascorbic acid and sodium ascorbate, will neutralize chlorine. Neither is considered a hazardous chemical. First, vitamin C does not lower the dissolved oxygen as much as sulfur-based chemicals do. Second, vitamin C is not toxic to aquatic life at the levels used for dechlorinating water.
You'll need about 52-104 oz of liquid chlorine per 10,000 gallons of water. This amount should get the chlorine level to between 5 and 10 ppm.
So if you buy liquid shock, be aware that it only lasts one to two months at the most before it starts to lose effectiveness. While many swimming pool chemicals stay good for years if stored correctly, some pool-maintenance supplies expire more quickly.
Pool chemicals should be stored in a cool, dry, well-ventilated place. Garages are generally not the best place to store pool chemicals unless they are locked in a storage bin or cabinet. Oxidizers and strong acids corrode metal and can cause heavy rusting of pool, electrical, and other equipment stored in the room.
Having too much chlorine in your pool water can be dangerous. Exposure to high levels of chlorine can cause lung irritation, skin and eye damage, and provoke asthma. Not only is it bad for your health, but it can be bad for your pool due to the increase in chlorine.
Lower the water temperature
If you are keeping your water temperature above 100 degrees when you are not using your hot tub, the chlorine can evaporate more quickly.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.
The extra filtering will help clean out the impurities rain has introduced into your pool's water. Pool pumps are made to withstand rain and it is beneficial to run your pump during or after rain.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
For the greatest protection against algae, bacteria, and cloudy water, Intex pools should maintain a chlorine level of 2.0-4.0 ppm at all times. If you opted for the Intex Salt Chlorinator, you can make your own chlorine by adding the correct amount of Pool Salt to the water.
You can swim with chlorine tablets in the pool if the chlorine tablets are in a container. Getting in touch with those tablets can cause rashes, irritation and eye problems. However, to be in a safe zone it will be better if you wait for 3 to 5 hours till the chlorine levels touch 4 to 6 ppm.
Often, it will look something like this. 12.5% Liquid Chlorine Pool Shock – Normal Dosage: 1 gallon of shock per 10,000 gallons of water. Shock Dosage: 2 gallons of shock per 10,000 gallons of water.