While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
pH Balance and Chlorine
Algaecide also works together with chlorine, helping the chlorine to be more effective against algae and bacteria.
Algaecide will work with the chlorine or oxidizer to kill and prevent white water mold from returning.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
Now is the time to add Pool Clarifier and let it circulate for 12 hours. This will clump the algae together into vaccumable pieces. Shut your pump off and let the cloudiness settle. This may take up to a few days for very cloudy pools.
Chlorine—yep, your typical sanitizer—is much more effective at killing algae than algaecide is. Even if your water gets cloudy and your walls get slimy, chlorine can still kill it. That's because chlorine oxidizes bacteria and single-celled algae, which means they trade electrons.
Algaecides treat and prevent pool algae, but not all algaecides are created equal. To treat green pool water, ensure you select an algaecide that kills green pool algae. After treatment, some dead algae may remain in your pool. Continue to thoroughly brush your pool's surfaces often.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
If you have a saltwater pool, your best bet is EasyCare PoolTec. This all-star algaecide that controls and prevents green algae, mustard algae, and black algae while delivering beautiful water clarity. Additionally, it's designed to boost the effectiveness of chlorine in pools that use saltwater chlorinators.
So if the pool water isn't cloudy and the 'dirt' is clinging to the walls after brushing, the problem is likely be yellow/mustard algae. Yellow/ Mustard algae is very resistant to even high chlorine levels and will grow and thrive in a chemically well-balanced pool.
It is best to wait 30 minutes after adding it to your pool. We recommend waiting at least 15 minutes to swim after adding algaecide to your swimming pool. Most algaecides are perfectly safe to swim with.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Pour the algaecide dose into the water, depositing it in several areas around the pool. Your swimming pool pump should be running at this time to help circulate the algaecide. Wait about 30 minutes before allowing anyone to swim after the algaecide application.
It could take up to 24 hours for the pool water to clear after treating with Algaecide. We suggest waiting at least 48-72 hours before adding any more items (shock, algaecide, etc) to your pool water. If there are no signs of clearing you may need to shock your pool or drain and refill with fresh water.
The algaecide in the kit can cause some foam if there is no algae in the pool to destroy – it lingers around with nothing to kill. Spring time algaecides use surfactants to work and these molecules can react with agitation to cause froth.
When the levels are properly balanced, chlorine will keep the algae at bay, but the water will slowly begin to turn green as the algae take over if there's not enough. But be careful—adding too much chlorine in pool water can cause those metals to oxidize and turn the pool a different shade of green.
A nylon or rubber brush is the correct choice for scrubbing the sides of a soft-sided above-ground pool. A large pool brush makes quick work of the job, but you may need a smaller brush to clean corners. Once the particles have been removed from the sides of the pool, turn your filter back on and agitate the water.
It's important to note that you should not try to vacuum green pool water until you have removed any and all organic debris using a pool net, and have added the proper chemicals to the water, and done proper brushing so that the green algae has visibly settled to the bottom of your swimming pool.
While green algae are endemic in salt water pools, they are the easiest to kill. Green algae tend to grow during summers when the temperatures can get high. They float freely in the pool, making the water green. You might even see them growing on the bottom of the pool, on the walls, or in the crevices.
It can be used in pools, fountains, and ponds. Pond algaecide,when properly used with fish and pond plants, such as water lilies, is a great solution to algae management.