Chlorine has a low pH level, and in order to maintain your pool water's clarity and balance, shocking weekly will allow you to quickly raise the chlorine level, which will rid the pool of contaminants, without lowering the water's pH levels.
If your total chlorine level is high, you will use a non-chlorine shock; if it is low, you will use a chlorinated shock. As a rule, you will need to raise free chlorine to 10 times your combined chlorine to hit what is known as “break point.” Therefore, it is good to deal with combined chlorine while it is still small.
It is critical to understand that using pool shock and algaecide together can cause bad chemical reactions if the necessary precautions are not taken. Since your chlorine levels will not return to normal right after you shock your pool, we recommend waiting at least 24 hours to add algaecide.
Adding chlorine besides the shock can increase the chlorine content in the water which can make the entire shocking process useless. Hence, it is better if you don't use the shock and chlorine at the same time. The best time to add chlorine to the pool water is after you have shocked the pool.
At the very least, you should have the following chemicals on hand whenever we're talking about treating pool water: Shock Chlorine Granules or pure liquid chlorine. Chlorine tablets or Stabilized chlorine (if not using a salt water chlorinator) pH Regulators (pH up and pH down)
You should not add all pool chemicals at the same time. You should also avoid mixing pool chemicals together. Adding chemicals at one time can cause dangerous chemical reactions and serious injuries. In addition, it will make it difficult to balance the pool.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment. Improve filtration with a pool filter cleaner or filter aid like Jack's Filter Fiber.
The best time of day to shock your pool is in the evening. This is because the sun's rays can affect the effectiveness of the chlorine by dissolving it too quickly, before it has a chance to rid the pool of contaminants and clean the water.
Wait times for adding pool chemicals
The wait times between adding pool chemicals is usually around 10 minutes each, as that is also sufficient time for the chemicals to mix in the water. Users also under normal conditions can swim roughly 10 minutes after adding chemicals.
It takes about 24 hours for the chemicals to properly circulate in order to get an effective reading from the retest. The water test will assess the pH, chlorine, total alkalinity and calcium hardness. If you use chlorine in the pool, you should also test for cyanuric acid.
6. Add chlorine until the chlorine level is between 1.0 and 2.0. Although some sources allow chlorine levels as high as 3.5, this may be irritating to skin and eyes. Allow 24 hours for the pool chemicals to stabilize.
Sodium hypochlorite (also known as liquid chlorine) is another frequently used option for shocking pool water. This is a common choice in pool shock because you can pour the solution directly into the pool without having to dissolve the chlorine in water beforehand.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
Generally speaking, the dosage amount of pool shock is 1 lb. per 10,000 gallons, but consult the shock package label.
Unfortunately, you can't shock your pool using your regular 3-inch chlorine tablets. Common chlorine sanitizing products are great for maintaining chlorine levels, but not necessarily eliminating new waste, bacteria and algae.
Extra Tips. Make sure pool has been running for at least 15 minutes. An hour is ideal.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Adding more chlorine to your pool will kill bacteria, pollutants and any other unwanted organisms in the water. Most people wait until they have a cloudy pool or pool algae to shock their pool. However, adding shock to your pool on a regular basis can help you avoid pool water problems.