Clorox itself recommends using between 100 and 200 ounces of regular-strength bleach per 10,000 gallons of pool water -- one gallon is 128 ounces, and many bottles of bleach are available in one-gallon or half-gallon sizes. Pool professionals tend to recommend more conservative amounts of bleach.
Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine. Household bleaches often have unwanted fragrances and colors.
The solution to maintaining a clear pool is to use readily available liquid bleach as your chlorine source. Chlorine bleach, as discussed above, is not bound to a stabilizer, so when you add chlorine bleach to the pool, it will go right to work killing microbes and sanitizing.
If you need to mildly shock a 30,000-gallon pool by raising the free chlorine concentration to 5 ppm, you need 2.5 gallons of bleach. To raise it to 10 ppm, you need 5 gallons.
Answer. There's a protocol when using Clorox® Regular Bleach2 for swimming pool disinfection. On an ongoing basis, if you super-chlorinate the pool with 100-200 oz. bleach per 10,000 gallons of water, in addition to regular chlorination, algae growth can be prevented.
High concentrations of chlorine (above 1.5 ppm) will attack the liner and bleach it, thus damaging it. Any level below this range will weaken its ability to kill off bacteria.
What can you use instead? Bromine — considered a safe substitute for chlorine. Looks for BCDMH tablets, which are typically 66% bromine and 27% chlorine. If unable to find, you can use just bromine but it may leave the water a dull green color.
It is a good idea to wait at least 20 minutes after adding the water balancing chemicals. If you use calcium chloride in your pool, you should wait at least 2 hours to swim.
If you need to calculate how much bleach or Clorox you need to shock your pool, you will have to use 1/2 gallon of bleach per 10,000 gallons of water to raise the chlorine levels by 5 ppm.
Green algae, unlike its black counterpart, is a true algae; it isn't resistant to chlorine, so you can control it by shocking the pool. If you don't want to spend a lot of money on expensive pool chemicals, you can shock with household bleach.
Well-known member. No! Splashless contains a type of soap as a thickener, and it will make bubbles in your pool, as well as HE washing machines. Don't use splashless bleach.
In a clean, freshly filled 500 gallon wading pool, add a quarter cup of unscented household liquid chlorine bleach to the water. Then, at the end of each day, test the water and add an additional 1/8 to 1/4 cup, depending on the reading.
Common unscented household bleach (sodium hypochlorite) works well to shock a pool.
It is possible use use the tablets in your large wading pool. However, this is not economical and it will take a large amount of tablets to clean your pool. Unless you have a major supply of these tablets on hand, I would not suggest using them to clean a pool.
Chlorine is a natural element and an ingredient of bleach, while bleach is a solution and the product of combining chlorine and other chemicals. 2. Chlorine exists in nature, while bleach is a manufactured product.
*1 gallon of chlorinating liquid delivers the same amount of chlorine as 2 chlorinating tablets.
Answer: It is true that pool chlorine is stronger than bleach. For bleach and water to be the same strength as pool chlorine and water, you would have to adjust the ratio, increasing the bleach and reducing the water. But no matter which chlorine you use, make sure to test a small area before doing the job.
Of course, too much chlorine in pool water can be dangerous. Exposure to over-chlorination can provoke asthma, lung irritation, and potentially skin and eye irritation. As well as being potentially bad for you, it's bad for your pool.
Best time is either after sunset, or when you need it. Bleach doesn't lose concentration overnight unless it has something to work on. In fact, a good way to tell if your pool is in good shape is to do an overnight chlorine test. Ideally, the FC at night should be the same as the FC level the next morning.
Potassium peroxymonosulfate: A less costly, non-chlorine shock. Add it directly to your pool water at any time. Takes roughly 15 minutes to work before you can safely swim.
Pros of Saltwater Pools
There's less chlorine and less of the heavy chemical scent and content. They're gentler on the skin, with less irritation to the eyes, hair and swimsuits. The water has a softer, silkier feel to it compared to chlorine water. They have lower maintenance costs than chlorine pools.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity.
To mix chlorine bleach combine 5.25 percent sodium hypochlorite and 94.75 percent water. To mix non-chlorine bleach, combine equal parts hydrogen peroxide and water. Pour mixture into the plastic container, and secure tightly. Shake to mix ingredients.