If you hear 1 long beep, it means that the turnpiece rotated to locked position. If you hear 10 short beeps and 10 short red flashes, it means low battery.
Amber flashes mean it is locked, while green flashes mean it is unlocked, and red means low battery.
A flashing red light on your Smart Lock indicates that your batteries need to be replaced. To resolve this issue, replace your existing batteries with a fresh set of 4 brand new AA Alkaline batteries. It is important to replace all 4 batteries at one time.
How do I know when the batteries are running low on my Smartclode 909/910 deadbolt? There are two low battery indicators on the unit. The LED light on the interior side of the lock will flash red when the batteries are low. The keypad will also flash red when the batteries are low.
Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. 3. Press the Program button once more. When the LED flashes green and you hear two beeps, the lock has been reset.
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.
My Keypad Is Unresponsive
Test each button on the keypad (one at a time), and listen for a beep as each button is pressed. If beeping is not heard on all buttons, replace the batteries. If battery replacement does not solve the problem, contact Kwikset Support at 1-866-863-6584.
If you hear 2 short beeps, it means that the turnpiece rotated to unlock position. If you hear 1 long beep, it means that the turnpiece rotated to locked position. If you hear 10 short beeps and 10 short red flashes, it means low battery.
Replace batteries with new ones to ensure that lock is properly powered. Typical battery life based on 10 entries per day is 10-12 months if the door is properly aligned and the lock does not encounter interference in lock/unlocking the door.
A fresh set of four AA alkaline batteries will last approximately 6 months depending on usage.
If it's blinking red it means that it's low on battery and it should show plain red when it's charging and will light up blue or green when it's full.
The red key warning light means there is a security error code. This light illuminates when the vehicle control modules see the ignition turned with a key that is not programmed to the vehicle or when there is an error within the security protocol of the vehicle's security system.
Your door handing code has not been entered. Enter door handing code and test lock on page 7 here.
The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt.
Your Smart Lock will give you low-battery warnings for multiple weeks before it loses power. However, if your Smart Lock dies entirely before you can replace your batteries, your key will still work. This is the same deadbolt key that you've always used - the Smart Lock doesn't change the key needed.
No, user codes will not be lost if the batteries die or are removed.
The recommended batteries to use in your Door Lock are AA alkaline, non-rechargeable batteries. Make sure there are no lithium NiCad batteries in use.
Check door alignment. Even the slightest misalignment between the door bolt and the strike plate hole can cause increased friction, which requires more power to successfully lock and unlock. This is by far the most common contributor to decreased battery life and should be assessed first.
On my Smartcode Deadbolt, Keypad flashes red 15 time with 15 beep (beeping sound will only be heard if switch #3 is on) You've entered three incorrect codes within one minute. Please re-enter your code after 60 seconds keypad lockout.
This usually means that the lock is in low power mode and will likely not function as expected until the batteries are replaced with brand new batteries.
Make sure the User Code is correct and that the Kwikset button is pushed after entering the User Code. If the door still won't unlock, use a key to unlock the door. Call technical support for further troubleshooting.
If the smark lock is not responding, the issue may be communication. It's possible that the smart lock won't calibrate or connect with the panel. Try rebooting the door lock by removing the batteries. Removing the batteries will force the device to reset.