It is common to mix bleach with water; however, you can also add other ingredients to make it more effective. Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
However, you should exercise meticulous care and caution since bleach can discolor your brick pavers and thus ruin your precious hardscape. Since bleach can have such strong impact on your hardscape and lawn, you should test it first in a small and inconspicuous patch.
Whether your patio is sealed concrete or cement, or even sealed concrete pavers, a bleach and water solution makes it easy to clean away built up soil, stains from leaves and pollen, mold, mildew and algae.
Usually, hosing them down once a month is sufficient. Use soap and water, if the pavers are still dirty after sweeping and water hosing, make a solution of soap and water. You can use dish soap, laundry detergent, or any type of general-purpose cleaner. Never use bleach on your pavers, as it can damage the surface.
Use Bleach
But that's not all; chlorine bleach can also be used for cleaning the concrete driveway. Of course, you should dilute it with equal parts of water or a 1:1 ratio. With the mixture ready, spray it on the driveway, allowing it to sit for 10 minutes. Then, use a stiff brush before rinsing with clean water.
As a gentler cleaner, bleach can't harm concrete's durable material. Aside from being an effective cleaner and stain remover, it also acts as a disinfectant to the concrete surface.
In fact, vinegar removes mold from concrete better than bleach. Bleach will only remove the top layer of mold, causing the mold to return.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
Use Vinegar or Bleach
If you are going to try this approach to remove mold or algae, first try a mixture of white vinegar and water to spray down the area and kill the mold.
Apply the bleach and water to the wet paving slabs
Brush the solution to make sure you get an equal coverage of the cleaner. Make sure you brush the cleaner into all corners of the paving slabs. Once applied leave the cleaner on the surface for 10 -15 minutes.
The pressure washer in combination with a dirt cutter is an excellent option. This removes not only weeds and moss from the surface, but also from indentations. Keeping up with this type of cleaning means that there is less time for weeds to grow. It also helps to maintain the beauty of the paving stones' surface.
OxiClean is a powerful concrete cleaner that works well on various materials, including pavement and grout. This concentrated solution provides excellent cleaning without leaving residue.
A mix of water and vinegar is a great combination to remove stubborn dirt and stains. If you want even better results, use this mix with a cleaner solution specific made for pavers or soap and water.
And, while it may be tempting to use household bleach for a quick clean, Beril says that this can ruin the patio stones and leave them looking patchy. 'There are many specialist patio cleaning products on the market including brick acid,' she cautions.
First, you'll need to make sure that there's no run-off of the bleach onto any surrounding plant life. Plants that come into contact with bleach will die. Second, bleach isn't suitable for man-made concrete slabs – only natural paving stones. Bleach will fade artificial slabs over time.
Mild detergent and water.
If your pavers aren't too dirty, this can be a quick and easy way to clean them without any fancy equipment. Mix some mild dish soap with water in a bucket to create suds, then use a brush or a sponge to scrub the surface of the pavers.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Can you power wash pavers? Power washing (also known as pressure washing) is also a very effective method by which you can remove dust deposits and various stains from your pavers. Just make sure that the water jet is not directed directly at the joints between the paving stones.
Depending on the material of the paver (non-coloured concrete is safe), CLR may be suitable. Always spot test in an inconspicuous area first. Make sure the pavers are not coloured, stamped, sealed or coated.
Baking soda has low-abrasive properties, making it an excellent cleaning material for stuck-on grime and tough stains. Additionally, baking soda is absorbent, allowing it to absorb oils from the surface of the pavers, especially freshly oil spill on concrete pavers.
Bleach is commonly used to whiten concrete and is very effective at doing so if the initial stain is removed beforehand. Bleaching stained concrete white prepares it for any additional coloring treatments that you may wish to apply in the future.
Cleaning vinegar or white vinegar – not apple cider vinegar or wine vinegar – is most commonly chosen for cleaning. However, it's important to remember that while vinegar does work as a disinfectant to some degree, it is not as effective as bleach or commercial cleansers when it comes to killing germs.
Although bleach is great at the whitening effect, you can use peroxide to achieve this. Hydrogen peroxide is an oxygenated bleach. It is safe for plants, so when you rinse this solution, it won't harm anything. It works together with the dish soap and baking soda to remove dirt and whiten dirty concrete.