If the pool is still very cloudy or green, you may need to shock it to make it safe to swim in again. First, make sure that the filter system is working properly and the chemicals are still at the proper levels. Next, mix up your chlorine shock (hyperchlorinate) treatment.
If your pool is still green after 24 hours, there may be too much of the wrong chemicals, for example an excess of phosphate or cyanuric acid (“stabilizer”). It will take a while for the cloudiness to go away. For a sand filter, it will take a week or more.
Shock the pool with chlorine every day until all the green is gone (possibly 3 to 4 days). 2. Run the filter 24 hours a day and backwash every day until the green and then cloudiness is gone (usually up to 7 days, sometimes as long as 2 weeks depending on the filter). 3.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
The free chlorine levels might be low.
But be careful—adding too much chlorine in pool water can cause those metals to oxidize and turn the pool a different shade of green.
Baking Soda and Green, Blue, or Yellow Algae
You'll need to use an algaecide to kill the algae and superchlorinate your pool to clear the water. After this treatment, test your pH and alkalinity and add baking soda to raise alkalinity to at least 100 ppm and pH to between 7.2 and 7.8.
In theory, if you have a cloudy swimming pool, you can add chlorine to “shock it” and clear things up. Chlorine will get the job done. But, the amounts may vary and you may have to really pound the pool with chlorine to get the water totally clear.
You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
Use a vacuum or backwash the pool to remove the dead algae. Apply a mustard algaecide following the label directions. Allow the water to circulate for 24 hours. Use a pool vacuum or backwash the pool again to remove the remaining dead algae.
Use chlorine as your go-to algae killer.
When your pool water is green or contains visible algae clumps, your pool does not have enough chlorine. "Shocking" the pool with a large dose of chlorine is the most effective way to kill the existing algae and bring your pool back to sanitary conditions.
Clorox itself recommends using between 100 and 200 ounces of regular-strength bleach per 10,000 gallons of pool water -- one gallon is 128 ounces, and many bottles of bleach are available in one-gallon or half-gallon sizes. Pool professionals tend to recommend more conservative amounts of bleach.
Just as was said earlier, white household vinegar is the most preferable for lowering pH, and it can be applied by adding it directly into the pool without necessarily diluting it with water.
Just like you run vinegar through your coffee pot to get rid of calcium buildup, white vinegar can wipe away this eyesore in your pool. Mix a 50/50 solution of vinegar and water, dip a sponge or soft cloth into it, and scrub that residue away.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
You will need to quadruple shock your pool by added 4 pounds of shock to every 10,000 gallons of water. This can be expensive if you have a large swimming pool.
But is it safe to swim in a pool with algae? Whether mild or severe, it isn't recommended. Significant amounts of swimming pool algae welcome a breeding ground of harmful bacteria that feed on algae. These bacteria pose health risks to swimmers, most commonly resulting in a skin rash.
The most common form of algae in swimming pools is "green" algae. Green algae varies in color from blue-green to yellow-green to dark-green. It can be free floating in the water (turning the water a hazy green) or can cling to the wall-clinging (patches of green).
All you need to do is bypass the filter and pool vacuum for algae to the waste. However, this can only work if you have a multiport system or a waste line system in your cartridge filter. Vacuum the pool to waste after you have set up the waste, and the debris and algae will get out of your pool.
Grab a brush and some baking soda. Bicarbonate, the active ingredient in baking soda, is an effective spot treatment to help kill the algae and loosen it from the wall.
A nylon or rubber brush is the correct choice for scrubbing the sides of a soft-sided above-ground pool. A large pool brush makes quick work of the job, but you may need a smaller brush to clean corners. Once the particles have been removed from the sides of the pool, turn your filter back on and agitate the water.
Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you're using.