Your pump may be too large or the sand level too high in the filter. When the filter is backwashing the water flow can cause the sand to rise high enough and overflow into the standpipe, which will allow the sand back into the pool.
Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs. In general, you shouldn't be losing sand from your sand filter. Nor should any sand be coming out during backwashing, rinsing or filtering.
The most likely cause of sand at the bottom of your pool is that it simply fell in the water. This can happen even if you don't have sand around your pool. Wind can pick up sand particles and carry it long distances. So the wind may have dropped some sand in your pool on the way through the neighborhood.
A nylon or rubber brush is the correct choice for scrubbing the sides of a soft-sided above-ground pool. A large pool brush makes quick work of the job, but you may need a smaller brush to clean corners. Once the particles have been removed from the sides of the pool, turn your filter back on and agitate the water.
The sand in your pool filter needs replacing every three to five years, sometimes even longer if your pool remains in relatively good condition when it's open. If you run your pool filter often all year and have a heavy bather load, the sand may need replacing sooner than three years.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value's waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
How Often Should You Backwash a Pool Sand Filter? As a general rule of thumb, you should backwash and rinse your filter about once a fortnight. The optimal time is right after you vacuum the pool. However, if your pool has had a lot more use than normal, it may be necessary to backwash once a week.
On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
Replacement sand for your sand filter typically costs around $25 per 50-pound bag, and your filter may require 100 to 600 pounds or more depending on the size and model. More than likely, you'll need about 350 pounds of sand for an average-sized inground pool filter.
How Much Sand to Add to Pool Filters? Sand filters are not filled completely full of sand, but only about 2/3 full, to allow “Freeboard” space in the tank, above the sand bed.
Sand filters often do not filter 100% of algae. The more times a pool is shocked once you have algae, the smaller the particles get. Ideally, turning off the pump for a day will drop all the algae to the bottom and then you vacuum to waste.
Whenever the filter fills up with the dirt/debris it reduces the flow of water to your pool. Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear.
* Can i discharge the backwash water onto my lawn, will it harm the grass / plants? The DE doesn't harm the grass or plants, excessive chlorine or saltwater may.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.
In unsewered regions, backwash water is to be discharged to a grassed, vegetated or garden area, or a stone-filled trench either open to the surface or underground (similar to a septic tank absorption field).
For inground pools with a sand or DE filter, the easiest way to quickly lower the water level is to place the multiport valve into the waste position and roll out the backwash hose. If instead, you have a slide (push-valve), backwash the filter to lower the water level.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
You need chemicals with a sand filter because they require sanitization, phosphate removal, pH adjustments, and alkalinity alterations.
If you're not using chlorine, you should do it more often, about every three to five years. Chemical cleaning of the sand should take place about once a year usually or twice a year if you use a biguanide sanitizer./
Too much sand and your filter will likely not run correctly or may break when reassembling. Too little sand and you will have cloudy water no matter how much your filter runs.