When the pump shuts off, air is drawn into the system, which forces DE powder out the main drains or skimmer. After the system comes back on, some of the powder will be sucked back in and part of it may be left in the pool. Replacing the gasket on the pump should cost about $15.
CHECK MULTIPORT VALVE GASKET - If your Multiport Valve (MPV) Spider Gasket is damaged, you could have DE Powder leaking into the FILTER path during BACKWASH. A common cause of a damaged MPV gasket is the pool owner's failure to turn off the pump before moving the MPV handle.
This leaves your pool a cloudy, muddy-looking mess. Luckily however, the powder usually sinks to the bottom of the pool. The only way to remove the earth from your pool is to vacuum the pool with the filter release valve open. This will allow the earth to flush from the filter.
you might want to run the filter for at least 30 minutes. Depending on how much you use your swimming pool you should at least clean your DE Filter once a year. This means opening it up and washing down the grids and inside of the filter.
Chemically, it is safe to swim. You will need circulation in the pool to introduce chlorine...... keeping it sanitary and algae free. Do not turn your pump off for more than 24 hours or so.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
Potential Problems. Adding too much DE to your pool may cause multiple negative results. These ramifications include a clogged skimmer, turning the pool cloudy, reducing the circulatory pressure in the pool and putting too much work on your pump that may result in eventually breaking the pump.
The D.E. needs to be replenished once the filter is turned back on. Every three months the filter should be taken apart, the grids should be hosed off, and visually inspected for any rips or tears that will cause D.E. to blow back into the pool.
How Long Do I Have To Wait To Swim After Adding Pool Chemicals? It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool.
The most common reason for high pressure on your filter pump is a dirty filter. Whether you have a sand filter, DE filter or cartridge filter, dust and solid particles will slowly clog your filter causing the pressure to rise. To fix this, backwash your filter or in the case of cartridge filters, hose it out.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
If you do not add enough DE to your filter, then the grids are not totally coated with DE and the dirt that goes into your filter will attach itself right to the fabric on the grids and will not backwash off. This will cause your filter to short cycle (go very short times between backwashing).
Connecting the vacuum system to the pump.
Now, here answers the question earlier: do you leave skimmer basket in when vacuuming pool? YES, you need to remove the skimmer or strainer basket before attaching the open end of the hose to the inlet. Finally, plug the open vacuum hose into the suction port.
If dirt is reappearing at the bottom of your swimming pool after you've vacuumed it your pool's filter may be working poorly. Pool filters often work poorly because they're in need of cleaning. If you have a sand filter for your pool you need to make sure that the sand is sharp and freshened up.
For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The "Filter" setting is used for light to moderate levels of pool sediment.
The last thing you want to do is vacuum algae manually, which will contaminate your filter. Your pool will not clear up. In fact, the chances of your problem getting worse are very high. You'll also need to vacuum to waste when there is a large amount of debris or leaves in the pool, usually at opening.
A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
If anything could be considered “normal”, it would be about 10 psi. Most filter systems are designed to operate in the 5-15 or 10-20 psi range. The way to find out your particular correct pool filter pressure is to clean or backwash the filter thoroughly and empty the pump and skimmer baskets.
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
Knowing When to Replace Grids
Those with a DE filter should be opening up their filter and cleaning the grids every three months or more often. DE filter grids can last for four or five years with proper care.