Issues with the pilot light, high limit switch, blocked burners, leaky ductwork, electrical problems, and blower motor failures are common reasons for HVAC systems blowing cold air. These problems often require professional maintenance and repairs.
A clogged filter is one of the most common causes of a heater blowing cold air. However, even if you replace the air filter with a new one, dirt, and other particles can still be inside the system. This could lead to overheating in the long run.
First, check to make sure the thermostat is set correctly. You will want to make sure that the fan control is set to auto, and not 'on'. If the thermostat appears set correctly, turn off your heater at the thermostat and check the filter. If the filter is dirty, replace it.
While furnaces can stop operating for complicated reasons, home owners should check a few usual suspects first behind a lack of hot blowing air: Electrical problems causing a loss of power. Blocked air vents and ducts restricting airflow. Improperly configured thermostat settings.
Blocked registers or vents can also cause a heater breakdown in the same way that clogged air filters do. If your HVAC system can't take in enough air, it will be unable to distribute warm air. It is also worth noting that occasionally a vent will get closed by accident.
When your furnace runs but fails to blow air, several issues could be at play: Blower Motor Problems: If the motor is malfunctioning or not receiving power, it can't push air through your ducts. This could be due to electrical issues, a faulty motor, or problems with the motor's capacitor.
If your furnace is blowing hot but your home is still cold, it may be a problem with your ductwork. You may have leaky or damaged ducts that are letting hot air escape and cold air in. Sometimes a damper in the system can get miss-adjusted or come loose, thereby inadvertently blocking or reducing airflow.
If your furnace turns on but no heat is produced, there may be a problem with the fuel supply or the ignition system. If something is stopping your furnace from receiving gas, there is no fuel to combust so the furnace will not create any heat. The furnace turns on but no heat comes out.
Obstructed Vent
Furniture, bedding, and the vent damper could all be possible obstacles to the vent. If you find any closed or blocked vents, you can clear away the obstruction and feel for airflow, but if your vents are open and still not blowing enough air, there could be an issue with the fan's motor.
Issues with the pilot light, high limit switch, blocked burners, leaky ductwork, electrical problems, and blower motor failures are common reasons for HVAC systems blowing cold air. These problems often require professional maintenance and repairs.
A Recap of Why the Thermostat Says Heat On But No Heat Comes from the Furnace and What to Do About It. Dirty air filter–Change it. Gas supply turned off–Turn on the valve or call the gas company. Incorrect thermostat settings–Review all the settings and change them if necessary.
Therefore, your furnace blowing cold air could result from a clogged or dirty air filter. If you have a dirty or clogged furnace filter, the cool air from inside your home will struggle to travel through it and into the furnace. This means you have insufficient air to heat and redistribute.
In most newer systems, the button is often directly next to the blower motor, while in older systems, it may be harder to spot as it is sometimes underneath or behind the motor. The reset button is often made of yellow or red plastic and marked with a large “R ” to make it easier to spot.
It's most likely an incorrect thermostat setting if you find your furnace blowing warm air, not hot. The fan is set to “on” instead of “auto.” Furnaces only pump hot air until the thermostat setting is reached, so if your fan is always on, it will blow both hot air when the furnace is heating and cold when it's not.
Most modern thermostats will have a clearly marked reset button inside the panel. It's usually small and recessed, so you might need a pointed object like a paperclip to press it. For those wondering specifically how to reset air conditioner thermostat models, the process is generally the same.
There's a problem with your filter.
If the airflow to your heater is restricted, it can trigger your furnace burner to turn off while the blower keeps running. This will make the air just warm (or chilly). Common filter issues that restrict airflow include:. Filthy air filters (Change it!).
Check the Air Filter
If so, there is a good chance that the filter is too dirty to allow the furnace to work properly. A dirty air filter can interrupt the airflow over the heat exchanger and cause overheating problems. At this point, the high-limit switch will trip for safety reasons, causing the burners to shut off.
You can generally identify a blocked air duct by a distinct drop in heating and cooling efficiency, increased energy costs, and occasionally a musty, dusty smell throughout the home. The blockage usually comes over time, by a buildup of dust and debris that just accumulates until it begins choking the system.
The most common reason your furnace is running but not blowing air is likely due to issues with the blower, blower motor, or blower module. The blower pushes air out of the registers and pulls air into the return registers.
Possible causes include a broken thermostat; the thermostat being set too low; an out pilot light; a blown fuse or circuit breaker; a closed gas valve; or electronic ignition problems.
You can reset the ignition on your furnace simply. To do this you must cut the power to the furnace first by turning off the circuit that powers it. Once the power is off you can remove the burner door to reveal the ignitor. Turn this to “off” and leave it off for at least 5 minutes.
This problem often points to inadequate circulation of warm air. It could be due to blocked vents, a failing HVAC fan, or issues with the furnace itself. Ensure that furniture or drapes are not blocking your vents.
If you're cold even though your thermostat indicates you shouldn't be, your furnace likely isn't the problem. In most cases, it's working just fine. It's your home that needs attention. Lack of insulation, severe air leakage, and/or unbalanced ductwork are frequently to blame.
Dirty or worn flame sensors, blower motor problems, clogs in the condensate lines, and electrical issues are some of the many problems that can leave your HVAC system failing to deliver the temperatures you've programmed in your thermostat.