If the igniter doesn't glow, then one of the components in the ignition system is broken. Use your multi-meter to check the wiring, igniter and safety gas valve for continuity.
This means either the igniter is faulty or the gas valve is faulty unfortunately and will need to be replaced. The igniter can glow and still be faulty. The best way to determine is to check the amp draw on the igniter. It should be 3 approximately 3 amps. If not, the igniter is faulty and will need to be replaced.
The igniter could be dirty, or clogged. Try cleaning it with soapy water and a brass wire brush. If that doesn't help, a replacement igniter can be easily ordered and installed.
Between 5-15 seconds, you see the igniter getting brighter (orange color).
Igniter. You'll pay $150 to $250 to repair the igniter. Igniters are crucial parts of gas ovens, as they are responsible for igniting the gas to give heat and cook your food.
A gas oven igniter works by sparking and heating the gas emitted from the oven, so without it, the oven will not be able to produce heat. However, as so much rests on this little igniter, they are prone to a bit of wear and tear.
The Spark Module Is Broken
The spark module provides power to the igniter, which lights the stove. When it's broken or not functioning properly, you probably won't hear the stove clicking and have no spark.
If an HSI is exposed to higher voltages than it's supposed to receive, they will surely break sooner than they should. An 80-volt HSI should have about 80 volts applied to it. Applying 120 volts to that HSI will cause it break, and sometimes almost immediately.
Reset The Furnace Ignitor
Find the burner door on the furnace and look behind it to find the ignitor. Turn it to “OFF” and wait for five minutes. After you wait, turn it back on and return the door to the burner. It is important to make sure the switch on the door is properly engaged.
Answer: Gas oven burners ignite in approximately 30 to 45 seconds. The infrared broil burner will light within 45 seconds. If it takes much longer than this to ignite, the burner may be experiencing delayed ignition, refer to Gas Oven Delayed Ignition for more information.
Clean any food debris out of the burner with a toothpick or compressed air. While you're at it, clean the grate, cap, and case. Check the wires connecting the igniter to the control module. If there's a loose connection, tighten it.
Answer: No, this is not possible due to the gas being controlled by the gas safety valve. You need the igniter to be working properly before gas is allowed out of the gas safety valve.
Inspect the pilot hole and use a wooden toothpick to clean it out. If the buildup is excessive and cannot be removed, you will need to replace the igniter to restore your gas oven. Once you are done cleaning, turn on the oven and observe the igniter to see if it glows red-hot during the ignition process.
If the igniter doesn't glow, then one of the components in the ignition system is broken. Use your multi-meter to check the wiring, igniter and safety gas valve for continuity.
DOES THE IGNITER MAKE A CLICKING NOISE? Make sure that the igniter is making a clicking noise when you press the igniter button. If it doesn't click, then the wires may not be connected properly, the battery may be dead or installed incorrectly, or the igniter module may have failed.
Because of this, igniters have a 3-5 year life expectancy. They will eventually crack and need to be replaced. If you suspect that you have a damaged HSI, you will most likely be able to change the part yourself. Like a light bulb, they are a regular replacement item.
The most common reason a gas stove won't light is that the igniter is clogged with debris. Over time, dirt and dust can accumulate on the igniter and prevent it from sparking. If this is the case, you'll need to clean it off in order for the stove to work properly.
The first thing you need to do before replacing your igniter is to purchase a replacement part. These can be found at all major hardware retailers and many online stores. Just make sure you double-check you're purchasing the correct part, or you'll need to return it.
A spark igniter electrode is made of metal and the base of the igniter is ceramic. This ceramic base can withstand the high temperatures put out by the burners. The ceramic is fragile and over time may crack or may have other damages and it may be shorting to ground and unable to ignite the gas flame.
You should typically lean toward replacing a wall oven only if it's older than 10 years, or if you're otherwise unhappy with your oven's performance and feel that buying a new model makes more sense. Most appliances are covered under warranty in their first year.
The rule of thumb is that if repair costs exceed 50% of the price to install a new oven, you should buy a new oven instead of replacing it. For example, if your oven costs $2,000 but costs $1,500 to repair, you could use that $1,500 for a new and improved oven.