Potential Causes and Solutions If your gas stove isn't lighting despite the clicking sound, it could be due to several factors. Common causes include gas leaks, faulty ignition systems, clogged burner ports, or issues with the gas supply.
If your pilot is lit and the fireplace isn't igniting when you push the button or flip the switch, the igniter may be dirty or defective. Clear away any dirt or debris that may be in the way between the igniter and thermocouple or thermopile.
A worn-out igniter can periodically fail, and if it keeps trying to light the gas, your furnace will make a clicking sound. The noise may last until the flame ignites or the gas valve closes.
Ok if it keeps clicking either the spark module is bad or the flame sensor is dirty and not working. When the pilot lights the flame hits the sensor and it is suppose to send a signal back to the module to stop sparking. I would clean the flame sensor off by the pilot light with some sandpaper and then try it.
If your fireplace doesn't light but you still have a spark, check the pilot light. Downdrafts or a worn-out pilot light will prevent your gas fireplace from turning on. You'll need a repair pro to install a new pilot light.
In the back of the burner, there is a small hole that feeds the gas through the igniter. Sometimes it can get blocked with grease or grime, which stops the gas from igniting. Use a toothpick or needle to give the hole a good clean. Put the burner back on the stove, and check if it now ignites.
One of the most common problems faced by homeowners with gas fireplaces is the pilot light going out or not staying lit. The pilot light is a small flame that ignites the gas burner, which produces the heat for your fireplace — if the pilot light goes out, your fireplace won't work.
A gas stove clicking but not lighting can be frustrating. Several common reasons can cause this issue, such as: A faulty igniter: The igniter, responsible for creating a spark to ignite the gas, may be malfunctioning. If the igniter is weak or damaged, it may not produce a strong enough spark to ignite the gas.
Gas furnaces rely on a smooth ignition process to kickstart the heating cycle. Clicking noises during ignition could signify issues with the pilot light or electronic ignition system. Solution: Schedule a professional inspection to clean or replace the pilot light, ignition components, or flame sensor.
If the igniter is glowing, but the burner is not lighting, the igniter may be weak and still be at fault because it requires a certain amount of current draw to open the valve. This check requires the use of an amp meter and should be performed by a qualified person.
Cause: The igniter may be damaged, worn out, misaligned, or covered in debris. How to Troubleshoot and Fix: Inspect the igniter for visible damage or misalignment. Ensure the igniter is clean.
If the valve is defective, it will probably make a lot of rattling and humming noises. If this is the case, you should have a qualified engineer look at it to get it running again and ensure it's safe.
So you've checked your pilot light and even reset it, but still, it wont stay lit. This can be an indication that your fireplace thermocouple is either bad or worn out. However, if your pilot is lit but the gas fireplace isn't, then there's probably a problem with your thermopile.
Gas fireplace igniter replacement cost
A gas fireplace igniter costs $90 to $150 to replace, including labor. This component uses electricity to ignite the gas and start the fire. Over time, the igniter may stop working from age or damage.
There are many reasons why a gas stove would stop working, such as the gas or power going out, food debris clogging the igniter, or a broken spark module. Schedule a service professional to assess your gas stove.
Most likely, your furnace is making a clicking noise and not providing heat because your furnace's spark igniter is trying to ignite your pilot light or burners but is failing to do so. In other words, there's an ignition system malfunction that needs to be fixed. Otherwise, your furnace won't start.
Short cycling is a common sign of a bad flame sensor. The sensor thinks that there isn't a flame, so it shuts off the gas as a safety mechanism. Except, there is a flame and without the gas to supply it, it dies. This is a frustrating problem, but an HVAC technician can fix it.
If you have heating but your boiler isn't firing up for hot water – or the boiler is clicking but not igniting – then it's likely that you have a faulty diverter valve. It's a common “wear and tear” issue that causes the valve to stick.
Potential Causes and Solutions
Common causes include gas leaks, faulty ignition systems, clogged burner ports, or issues with the gas supply. To resolve the problem, you'll need to identify the specific cause and take appropriate action, such as repairing the ignition system or cleaning the burner ports.
Your fireplace will make popping noises when it first warms up and especially when it cools down. This happens when the metals are expanding and contracting which causes these popping noises. This is nothing to be worried about.
You start smelling strange odors
This smell should go away after three to four hours of use. A dirty fireplace with excessive pet hair or dust can also produce an odor. If you smell rotten eggs, call for help immediately, as you likely have a gas leak.
Gas fireplace repair costs can range significantly from $400 to $1500, depending on the problem you face.