If your air handler is running but not blowing air, there are two likely scenarios: either a broken AC blower belt or an issue with the motor itself.
If your AC is on but not blowing air, check the thermostat settings first. A clogged air filter may also block airflow and needs replacing. The blower motor could be malfunctioning, or ductwork might be disconnected or blocked, affecting air circulation throughout your home.
It could be several things: IF it was working, then stopped, it could be the starter capacitor on the blower. If some vents are blowing good, but others are not, it could need balancing. It could be a clogged filter.
You go to turn on your air conditioner but nothing happens. Why? Usually, it means that your system is not receiving power or that your thermostat is not set correctly. Make sure that your thermostat is set to “cool.” You may also need to adjust the temperature that it's set to.
If the fan does kick on, but airflow is still restricted, check your air filter. If it is dirty, replace it. Check to see if your air conditioner evaporator coil is frozen.
If your air handler is running but not blowing air, there are two likely scenarios: either a broken AC blower belt or an issue with the motor itself.
In short, common issues that can cause an air conditioning unit fan to stop spinning are electrical issues, problems with the capacitor, contactor issues, a burnt out air conditioner motor, a broken fan belt, or clogged air filter.
In some cases, clogged air filters or dirty evaporator coils can also restrict airflow, forcing the AC to compensate by running at high power. To resolve this issue, it's recommended to check for clogged filters, clean coils, and consider having a professional inspect and repair the motor or fan control components.
It's a small, red button usually located on or around the unit. The button should have a clear 'reset' label. Once you find the button, press it for around three seconds and observe the AC. Check whether the AC kicks on immediately and if it doesn't, press the button again for another three seconds.
A bad thermostat can be detected when your AC or furnace is not turning on, your HVAC systems are not turning off, the thermostat not responding, your HVAC system is short-cycling, the room temperature not matching the temperature displayed on the thermostat, and the programmed setting resetting themselves.
Over time, the fan motor on the outside AC unit can wear out, causing the outdoor unit to stop working even when the inside AC unit is on. The fan motor can last 10 to 20 years with proper maintenance, like annual inspections and regular AC unit cleanings, but it will wear down faster without regular maintenance.
The short answer: Definitely not. (Unless you have manually engaged your outside fan to run constantly, but it shouldn't be running for hours on it's own.) If your HVAC is functioning correctly, it should keep your house cool by cycling on for 15-20 minutes at a time—with distinct pauses in between each cycle.
The thermostat sensor plays a crucial role in regulating the temperature inside your home. If the sensor is malfunctioning, it may send incorrect signals to the AC system, causing it to blow hot air. Regular maintenance and calibration of the thermostat sensor can help prevent such issues.
Installing a new heating and air conditioner blower motor could cost around $150 to $250, with most of that coming from labor costs. HVAC technicians usually go for around $75 to $125 per hour. A blower motor replacement might take anywhere from one-and-a-half to two-and-a-half hours.
You can generally identify a blocked air duct by a distinct drop in heating and cooling efficiency, increased energy costs, and occasionally a musty, dusty smell throughout the home. The blockage usually comes over time, by a buildup of dust and debris that just accumulates until it begins choking the system.
Shut off your system by hitting the isolation switch, wait 30 to 60 minutes and then turn it back on. This manual reboot fully disconnects your AC unit from power, allowing all electrical components to reset.
In the majority of cases, your AC system will return to functioning normally after this breaker reset. It's important to know that this isn't an instant fix and may take up to an hour to get back up and running as normal again.
First, make sure the register damper is open. Then remove the register cover and check for visible dust and debris clogging the duct. It's also a good idea to check your AC filter and see if it's clogged with dust. If so, get a new filter and replace it.
Power down your AC: Turn off your AC unit and unplug it from the power source. This will ensure that you stay safe while working on the unit. Locate the reset button: Most air conditioning units have a reset button located near the outside unit. It is usually a small button located inside a small hole.
Check these issues when the unit won't kick on: Check the thermostat and adjust the settings if it isn't set to Cool and an appropriate temperature setting to call for cooling. Examine the house circuit breakers for the AC unit and reset any tripped breakers. Check the air filter and replace the filter if it's dirty.
Check Your Air FilterOn the opposite side, if your AC and fan are both running and you still are not getting airflow through your vents, you will want to check for a dirty air filter. The air filter collects dust and debris and can block airflow through your system if not changed routinely.
A sure sign of a bad AC capacitor is a humming sound from within the access panel. Any humming noises indicate a problem with the air conditioning system or the components of the AC unit. Try turning the power on and off again to see if it was a one-time issue with the motor or a recurring problem.
If your ceiling fan isn't blowing air, one potential reason is electrical issues. This can be caused by a variety of factors including a blown fuse, loose wiring, a problem with the dual or single capacitors, or a defective motor.