Old pipes, especially ones made from metal, can corrode or rust from the inside. If mineral deposits are stuck in a water supply pipe, they can disrupt the flow to your shower (or other faucets). Similarly, if you have a small leak somewhere in your plumbing, low water pressure could be a noticeable symptom.
The most common cause of low shower pressure is a blocked showerhead, as a result of limescale build-up. These blockages obstruct the water flow, leading to reduced pressure over time. Most showers are fitted with a filter, protecting the pipework from debris, but this can become partially blocked by scale.
Most low-flow showerheads have a rubber pressure-reducing valve (called a regulator) to maintain a lower pressure. You can increase the flow by simply taking it out. You could also consider enlarging the hole that allows water into your showerhead with a drill to increase the amount of water coming through.
Depending on your current flow rate, you may be able to increase the flow simply by removing the filter or restricting device or replacing the showerhead with a higher-flow model, such as increasing to a standard 2.5 GPM head. Before you change the showerhead, make sure that the new model is legal in your area.
For water conservation purposes, most plumbing codes require faucets and showering devices to not exceed a certain maximum flow rate. Removing the flow restrictors could cause these devices to no longer meet these codes.
A high pressure shower head maximizes the flow of water through the shower head for a powerful spray. Waterpik® shower head engineers design water passages to minimize flow restriction and optimize the shower force, and put every shower head design through more than 1,000 hours of testing.
What does a flow restrictor look like? Before you remove the flow restrictor from your shower head, you need to know what it looks like. A water flow restrictor is usually a flat, circular, plastic piece. The center of the restrictor is shaped like a star, or similarly shaped, and comes in a variety of colors.
Pressure-Reducing Valve
Look on the main supply pipe near your water meter for a conical valve that has a bolt sticking out of the cone. To raise pressure, turn the bolt clockwise after loosening its locknut. Keep an eye on the gauge to make sure the pressure is within bounds, then retighten the locknut.
The short answer is low water pressure in your home arises due to a number of causes. Some include a shut or blocked water meter valve, mineral buildup clogs pipes, corroded pipes, or even a crack in the main city supply pipe to your home.
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992. The step down from there in Flow Rate is 2.0 GPM.
A water pressure regulator, if you have one, is usually located where the main water line comes into the house and after the main shut off valve. This way if you need to work on or change the water pressure regulator you can simply shut off the water main to do so.
Shower and bathtub shutoff valves are usually hidden behind an access panel. That panel can be in the bathroom, the room behind the bathroom or the ceiling of the room below. If you don't have an access panel, it could be hidden behind the wall.
Please keep in mind that all new faucets since 1994 are restricted to conserve water per EPA code mandates. Older faucets had no restrictions. Beyond intentional flow restriction, new installations can sometimes have reduced flow if the lines are not flushed prior to installation of aerators or shower heads.
Do All New Shower Heads Have Flow Restrictors? Not all new shower heads come with flow restrictors. While many brands focus on water and energy efficiency, it's not a universal feature. So, before you make a purchase, it's a good idea to check the specifications and ensure they fit your needs.
An easy way to upgrade a common tap, flow restrictors help save water by limiting the flow of particularly wasteful taps and showers.
The Fire Hydrant Spa Shower Head Spa Plaza is a good replacement shower head that is designed to boost water pressure in low flow settings. It has a 4-inch face to provide wide coverage, and this enables the water to reach all parts of your body.
A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
Removing a flow restrictor is illegal according to the US Energy Policy Act of 1992, which limits the maximum shower water flow rate to 2.5 gallons per minute (GPM).
National standard of maximum 2.5 gpm flow rate for shower heads was established through the Energy Policy Act (EPAct) of 1992 in order to save water. If the state, county or city of residency does not specify a maximum flow rates for shower heads, a 2.5 gpm shower head is the maximum one can get.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
Some of the first signs of a failing pressure regulator are a leaking water heater or commode. The water coming from a faucet may also exit with such force that splashing or water “hammering” may occur.