Most bathroom sink clogs result from a combination of hair, dirt, and skin flakes that bind with the gooey soap scum that accumulates on the walls of the drain pipes or gets caught on the pivot rod or stopper of the drain.
A major cause of clogged drains is mineral build-up in the system. For systems with hard water, mineral build-up can be an extremely costly problem. Over time the minerals found in hard water build up in your pipes, resulting in reduced water pressure, sluggish flow, and clogged pipes.
Use Filters and Screens
If you have had problems with clogs in the past, every drain in your house should have a wire mesh screen or similar kind of filter to catch debris, hair, and bits of food. These drains are one of the simplest and most effective ways to prevent clogging problems, so we highly recommend them.
If your snaking session yields plenty of hair and soap scum, but still leaves you with a slow drain, there's a good chance that the P-trap is still obstructed. To clear it, plug the overflow hole with a rag and fill the tub drain with hot water, which will help to soften and loosen soap scum.
Fats, Oils and Grease. These are the three most infamous kitchen sink cloggers out there. Unfortunately, they're also the most common. The problem is, these substances are all perfectly suited to clogging drains.
Fixes for Low or No Water Pressure in Bathroom Sink
Remove and clean the faucet aerator thoroughly, or replace it with a new one. Remove and clean the flow restrictor, increase the size of the flow restrictor hole, or remove it entirely and replace the aerator without replacing the flow restrictor.
Food, grease and other debris may be stuck in the pipe, causing your sink to drain slowly or not at all because the water hits a snag on its way down. The fix is disassembling the pipe to clean out the gunk that's causing the blockage.
Using a snake is also more invasive and time-consuming than using a chemical cleaner is, and can often become a dirty job. When it comes to getting at and removing major clogs or clogs that are deep down in your pipes, however, a plumber's snake is your best bet.
While snaking is generally considered safe for your pipes, it can damage your pipes if they are in bad shape. Homes that have older pipes are more susceptible to this happening as hairline cracks and corrosion occur over time. Surprisingly, snaking your main line can potentially make the clog worse.
First the drain snake loosens the clog—then the powerful Drano® gel clears it away! The 23-inch flexible tool bends safely through your pipes, and the Drano® Pro Concentrate Gel powers through the clog.
It is Extremely Corrosive For Your Drains
While it is dissolving your clog, Drano can also quickly eat away at the glue holding your pipes together, leading to a potentially costly leak.
You should schedule professional cleanings for your drains yearly even if they don't appear to need it and aren't blocked. In addition to annual professional cleaning for drains, maintain your drains weekly and monthly by performing certain care tasks.
You may be surprised to learn that pouring soda down the drain does work for some clogs. To be specific, you need a dark-colored cola (such as Coca-Cola or Pepsi). This type of carbonated beverage usually contains a good amount of phosphoric acid, which given enough time, can eat away at some types of clogs.
It's simple, the water in your pipes needs to go somewhere. If there's significant blockage in your pipes, then the water backs up. It's only a matter of time before that backed up water becomes a problem. Without addressing the problem of a clogged drain, flooding is bound to happen.
If water starts coming out of the drain in a main floor tub or shower, or if the toilets start filling up when you use a drain or run the washing machine, most likely you have a main sewer line clog.
Yes, it is possible for drain cleaners to end up making a clog worse. This can happen for a few reasons. First, the chemicals in drain cleaners can corrode pipes and cause damage over time. This can lead to leaks or even bursting, which can make a clog worse by creating additional blockages.
Over time, the plumbing pipes get dirty and accumulate debris, slowly blocking the water flow. This buildup of slime in the drain is a notorious breeding ground for bacteria. As it grows, the biological matter creates black sludge in the drain.
A plumbing snake is a very useful tool for clearing clogs and blockages from your drains and pipes, but unless you know how to use one correctly, it's best to call in a professional. The last thing you want is to make the problem worse or damage your drainage system!
Professional Plumbing Tools 101: Drain Augers
Also known as drain snakes, there are several different versions of drain augers that most plumbers will carry with them at all times. In essence, it's a basic tool, but an auger is best for tough drain clogs that just won't budge and for cleaning out drains, too.
Final Verdict. Our best overall pick for drain cleaners is Drano Max Gel Clog Remover, which also comes recommended by experts.
You need to make sure that you've securely tightened thumbscrew(the piece that secures the cable inside the drum or handle). If the thumbscrew is loose, the cable will not rotate at all when you twist the handle. The cable rotation is how the drain snake picks up debris, so if it can't do this, your auger won't work.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
Pour one cup of fresh baking soda down the drain, followed by one cup of white vinegar. Place a rubber stopper or other sink hole cover over the drain opening. Wait 15 minutes to allow the vinegar and baking soda to unclog your drain, Then take out the drain cover and run hot tap water down the drain to clear the clog.
Salt & hot water
While hot water can help loosen up debris, coarse salt actually scours the inside of your pipes, removing more material than hot water alone. After removing standing water from the sink, pour about half a cup of table salt down the drain before you pour in the hot water.