Cold air returns should be strategically placed throughout your home. You'll typically find vents or grills in every room or at least in every area served by your
Returns vents should be placed so that air flows from one end of the room to the other. If the supply registers are in the floor, then the returns should be near the ceilings. The returns are not determined by a number, but rather an amount of air flow.
You want to pull in the colder air so vents should face the floor!
Return vents should be located in centralized rooms, such as larger living spaces or family rooms. These central locations allow return vents to efficiently pull air from the house and into the system. In most cases, you'll find return air vents located on a wall instead of the floor or ceiling.
1. Openings shall not be located less than 10 feet (3048 mm) measured in any direction from an open combustion chamber or draft hood of another appliance located in the same room or space. 2. Return air shall not be taken from a hazardous or insanitary location or a refrigeration room as defined in this code.
Up High: having an air return higher up on a wall will be better at sucking in hot air that rises. Making it more efficient at transferring this hot air back into your system to repeat the cooling cycle. Down Low: if you have your air return lower on your wall it will function better as a cold air return.
Instead, there should be at least one return vent in every room, with two or three being ideal. If your house has only one return vent, this is not a problem — make sure to keep the doors open in every room so the air can circulate properly. Make sure there are no furniture, draperies, rugs, etc. blocking return vents.
Does Every Room Need Air Return Grilles? While it is a myth that air return grilles are required in each and every room in the house, it is definitely necessary to have more than one of these grilles installed at strategic places in the house. The most important place to have these would be the bedroom.
Symptoms include weak airflow and uneven cooling or heating throughout your home, with some rooms feeling much cooler or warmer than others. Homeowners should regularly check vents for consistent airflow. If you notice a significant drop in air pressure or uneven temperatures, it could indicate return air issues.
Where are cold air returns located? Cold air returns are located on interior walls in a home, typically close to the floor or low on the wall. You want to make sure that cold air return vents are not blocked or covered by furniture so that your home can get proper air circulation.
Return air ducts must be sealed and unobstructed — Sealing return air ducts is just as important as sealing supply ducts. Sealing all duct section connections with mastic, a specialized rubbery sealant, or with metal tape prevents air leaks.
One way to help combat this problem is to modify your cold air return ducts for better airflow. Whenever possible, expand your existing ducts vertically by cutting out pieces of wallboard and installing a new cover and air filter to fit.
Hot air rises and cool air sinks. Therefore, opening the right return vents in the summer and winter significantly improves the distribution of air by your forced-air system. You'll also enjoy more even heating and cooling throughout your home. In the summer, open your high returns and close the low ones.
If you have a combined heating and cooling system and need to decide between placing the return vents high or low, consider your climate. If you live in cooler climates, it might be wise to install them towards the floor, whereas if you reside in warmer areas, they should ideally be installed close to the ceiling.
Air Ducts Near the Ceiling Are Most Effective
Many people don't realize this because it is common to see air vents located near the floor in older homes. With vents near the floor, however, furniture often ends up blocking vents and causing the air to get trapped.
While return vents don't always require filters, adding them provides additional filtration, improving indoor air quality and keeping dirt and debris out of your system.
Can You Have Too Much Return Air? Too much return air coming through your system isn't much of an issue because the fans and ductwork working to get that air back into the system only pull with so much force to make the HVAC system work correctly.
Parts of Your Home Are Hotter or Colder
If there's not enough return air, your living room can be 10℉+ warmer or cooler than, for example, the bedrooms.
The Size Of Your Return Ducts
If you are installing just one or two return vents, you will want to go with a 12-inch return for 2-ton units and lower. 14- inches for 3 and up. 16-inch should be suitable for 4 ton systems, whereas 5 might require 18-inch returns.
Return air shall not be taken from a closet, bathroom, toilet room, kitchen, garage, mechanical room, boiler room, furnace room or unconditioned attic.
If you prioritize heating, put the HVAC and vents in (or below) the floor. This principle works for return heating vents as well. Place returns for cooling in the ceiling where the warm air congregates and heating returns in or near the floor where the cold air congregates.
One per room is ideal, but placing two or three in central locations can provide enough air circulation to maximize the energy efficiency of your HVAC and optimize indoor air quality, so your family stays healthy. If your home has multiple stories, you should have at least one return air vent per floor.
However, most HVAC contractors use a rule of thumb to determine the number of air vents needed. For example, for a standard residential HVAC unit, you'll generally need one supply vent and one return vent for every 100 to 150 square feet of living space.
In winter, enable the bottom cold air to return and in the summer, enable the upper return. It's that simple.
To identify a return vent, take a piece of paper and hold it up to the vent. If the paper is drawn towards the vent, then it's a return vent. Return vents are usually larger than supply vents, and they usually don't have adjustable slats to direct airflow since the air is going into the ducts instead of out.