Tip 3: Determine the most vulnerable side – When installing insulation with a vapor barrier, the vapor barrier should usually be applied on the side of the insulation that's closest to where it will be exposed to the most warmth and moisture.
As a general rule, many people who are trying to reduce summer cooling expenses choose to staple the foil to the bottom of the roof rafters, while people looking for a winter heat retention benefit opt for laying the foil insulation over the existing insulation.
In cold climates, the barrier goes on the warm (interior) side of the insulation. In hot, humid climates, it's placed on the cool (exterior) side. Under flooring: When installing wood flooring over concrete, a moisture barrier protects the wood from moisture damage.
A plastic vapor barrier is best installed in a vented attic within climates with over 8,000 heating degree days. If your climate does not meet these conditions, a vapor retarder like latex ceiling paint will work well for your house if you are in all other climates except the hot-dry and hot-humid.
You can use faced or unfaced batting when installing between the roof rafters of finished attic spaces. When using paper or plastic batting insulation, that moisture barrier should face outward toward the attic space. Even if the attic space is unheated, it's typically warmer than the outside air in winter.
Also, when laying down additional insulation, work from the perimeter toward the attic opening. Never lay insulation over recessed light fixtures or soffit vents. Keep all insulation at least 3 inches away from recessed "can" lights, unless they are rated IC (Insulated Ceiling).
Attic Ventilation
area shall be no less than 1/150 of the attic floor area if no vapor retarders are used, or 1/300 of the attic floor area when a vapor retarder having a permeance of one perm or less is used.
After the insulation is in place you will want to add a vapor retarder, sometimes called a vapor barrier, if you need one. Not every wall does. A vapor retarder is a material used to prevent water vapor from diffusing into the wall, ceiling or floor during the cold winter.
Vapour control layer building regulations
12 require that all new builds have an approved VCL fixed to the warm side of all insulation and cover the external framed wall area. It must be fitted at 250mm centres to the top and bottom of frames, around openings, at laps and wherever there has been any damage.
Because a vapor barrier is a low permeable barrier, it keeps moisture from passing through. This is beneficial to keep moisture away from a dry surface but will trap moisture behind it if installed on a water-damaged concrete wall, causing the wall to fail further.
Install a New Vapor Barrier
If your vapor barrier was damaged or not installed correctly, it's important to replace it with a new one. This will help prevent moisture from seeping into your crawl space and creating the perfect environment for mold growth.
General rule of thumb is that the WATER barrier goes on the exterior wall, just under the outer cladding, and the VAPOR barrier goes on the warmest side of the wall, up against the sheathing. You can have only one water barrier, and only one vapor barrier, so you would need to remove the existing one.
Some studies show that radiant barriers can reduce cooling costs 5% to 10% when used in a warm, sunny climate. The reduced heat gain may even allow for a smaller air conditioning system. In cool climates, however, it's usually more cost-effective to install more thermal insulation than to add a radiant barrier.
In unfinished attic spaces, insulate between and over the floor joists to seal off living spaces below. If the air distribution is in the attic space, then consider insulating the rafters to move the distribution into the conditioned space.
Generally speaking, vapor barriers are considered an essential moisture-blocking tool for climates that experience significant levels of humidity. For that reason, building codes in more humid locations will often require them, in which case you might not have much say about whether to install one or not.
The net free ventilating area shall not be less than 1/150 of the area of the space ventilated, with 50 percent of the required ventilating area provided by ventilators located in the upper portion of the space to be ventilated at least 3 feet (914 mm) above eave or cornice vents with the balance of the required ...
It is absolutely possible the ventilation system on your roof is excessive. Maybe your home is older and prior ventilation was installed by a homeowner, or incorrect vent sizes were used in an older roof layout. Too much ventilation can negatively influence the attic's and home's insulation as well.
Provided you're not claustrophobic, installing a vapor barrier is a project most homeowners can DIY. You will need to calculate the square footage of your crawl space, so you can buy the appropriate amount of liner.
Can I put plywood over insulation in the attic? Yes you can install plywood subflooring directly over the floor joists and insulation on your floor. You need to install rigid insulation boards on top of the attic flooring joists and then install plywood over the top.
Do I Have To Remove Old Insulation? Unless your insulation is wet, moldy or infested with pests, you don't need to remove it before adding insulation on top of it. ENERGY STAR® recommends that you inspect your insulation for signs of mold, mildew, moisture and pest infiltration before making this determination.
While loft insulation is an effective way to improve energy efficiency and reduce heating costs, over-insulating can lead to several potential issues. Firstly, over-insulation can lead to poor ventilation in the attic, which can cause moisture buildup and increase the risk of mould growth.