Smoke alarms with non-replaceable 10-year batteries are designed to remain effective for up to 10 years. If the alarm chirps, warning that the battery is low, replace the entire smoke alarm right away.
All alarms have a shelf life and may chirp when they've reached their end-of-life. If your alarm is older than 10+ years, it's time for a replacement. Chirping in newer alarms is most commonly caused by a low battery.
If a smoke alarm with sealed back-up battery is not out-of-date, shows the green light and still beeps occasionally, press the test button for more than 10 seconds to reset the alarm. If this does not help then you will need to replace your detector head.
Silence Button: Many smoke detectors have a ``silence'' or ``hush'' button. Press this button to temporarily silence the alarm. This is often effective for a short period, but the beeping may resume after some time if the battery issue persists.
To get the device to stop chirping once the battery has been removed, you must drain this residual charge by holding the test button for 15 seconds.
A: Remove the alarm from the mounting plate by rotating it counterclockwise (as indicated by the arrows on the cover of the alarm). Next, on the back side of the alarm, locate the area marked with a long arrow on the product label. Break through the label with a screw driver and turn the screw to the “OFF” position.
Clear Residual Charge to Stop the Chirp
Remove the alarm from your ceiling or wall. Open the cover and take out the battery. Press and hold the test button for 15-30 seconds. This will fully reset the smoke alarm and drain any charge left inside.
The beeping sound the low battery alarm makes can become very annoying but can be disconnected by removing the drained battery from your home alarm system panel. Make sure to replace the drained battery with a new one to keep your home alarm system functioning properly.
Hardwired Smoke Alarms
Identify which circuit breaker powers your smoke alarms. Each breaker should be labeled, so look for something that says “smoke alarm” or something similar. Turn off the circuit breaker for your smoke alarms. If your smoke alarms don't have battery backup, doing that will turn all of them off.
A single “chirp” every 30 or 60 seconds means the battery is low and must be changed. Chirping that continues after the battery has been replaced means the alarm is at the end of its life and the unit must be replaced. All smoke alarms must be replaced after 10 years.
Ten-year sealed battery smoke alarms are powered by sealed lithium batteries that have a life span of ten years.
If the smoke alarms give three beeps, then nothing, or any other kind of consistent but spaced-out chirps, there are two possible malfunctions: the device or the battery. If your alarm beeps once every minute for five minutes, this generally means it might be at the end of the device's life.
You can recycle smoke alarms and batteries at your local Household Waste Recycling Centre. If possible please remove the battery from the alarm. HOUSEHOLD WASTE FACTS: Most household waste types can be recycled or disposed of at local Household Waste Recycling Centres.
Most systems will begin beeping or chirping as a result of a total power outage or failure to recharge the system backup battery. For many of our most popular systems, beeping alarms and low battery trouble beeps can be silenced by pressing the [OFF] or [#] buttons from the keypad.
When you order on MyADT, your QSP provides one free system battery per year. Additional system batteries cost $29.99.
The alarm in your home security system is designed to be a deterrent to intruders, as well as alert occupants and draw attention to your home, whether that be from neighbours, passers-by or authorities. Systems will sound for about 5 to 10 minutes, depending on the system, before stopping and automatically re-arming.
If you have a wired smoke alarm, the chirping can be a sound of a low backup battery. If you remove the battery, it'll still carry on chirping because it thinks the backup battery is completely dead. In many models, a spring-loaded arm will pop out which makes it impossible to get the alarm back on the ceiling.
Clean The Alarm
Dust and debris can affect the alarm. As far as it is concerned, the spider web or speck of dust that is obscuring the sensor is a potential fire and therefore the alarm needs to be sounded. The easiest way to clean an alarm is to run a vacuum cleaner over the vent.
Stopping a smoke alarm from beeping is often simple. Get a step ladder and carefully reach for the alarm. Pressing the “Test/Silence” button on the front of the unit should stop it from beeping or chirping. If this doesn't work, grasp the device and turn it counterclockwise.
Previously, the replacement of smoke alarms older than 10 years was merely a recommendation. However, with the updated legislation, it has become a mandatory requirement. The rationale behind this change is rooted in the reliability and effectiveness of smoke alarms.
Consistent Chirping
An alarm will chirp every 30 to 60 seconds for a minimum of seven days. With a "low battery" announcement, disconnect the unit and replace the batteries. You can also put a unit into low battery hush for up to 12 hours on newer units by pressing the test/hush button.