If your pool water is still green, wait 24 hours and then redo the steps from Day 1. In the morning, add Oxidizer to your pool water. In the evening, add your liquid algaecide; we recommend concentrated 40% Algaecide.
Your chlorine levels won't return to normal right after you shock your pool anyway, so we recommend waiting at least 24 hours to add algaecide.
All algaecides work by releasing positive-charged ions into the water, which combine with the negatively charged algae particles. Algaecides don't break down in sunlight the way chlorine does, so they remain available much longer.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
Pour the algaecide dose into the water, depositing it in several areas around the pool. Your swimming pool pump should be running at this time to help circulate the algaecide. Wait about 30 minutes before allowing anyone to swim after the algaecide application.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
Let the water circulate for at least two hours.
Circulate the water for about 2 hours to ensure the flocculant is fully mixed in, then shut off your pump and let it sit overnight. During this time, the chemical will start to bind the particles together and settle them to the bottom of the pool.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
When closing and winterizing your pool, it is important to remember to balance your pool water's chemistry prior to closing and don't forget the algaecide. Algaecide is simple and effective with one quart of winter algaecide typically enough to treat 20,000 gallons of water all winter long.
GETTING RID OF ALGAE
Liquid Algaecide is a strong algae depressant used for the prevention of algae growth and the maintenance of sparkling water in pools. Algae growth is the main cause of “off” colours in your swimming pool water.
Use a vacuum or backwash the pool to remove the dead algae. Apply a mustard algaecide following the label directions. Allow the water to circulate for 24 hours. Use a pool vacuum or backwash the pool again to remove the remaining dead algae.
It could take up to 24 hours for the pool water to clear after treating with Algaecide. We suggest waiting at least 48-72 hours before adding any more items (shock, algaecide, etc) to your pool water. If there are no signs of clearing you may need to shock your pool or drain and refill with fresh water.
Recently Added Algaecide
There are a few different types of algaecides that contain various chemicals to suppress and fight off algae. Many of them include copper or copper sulfate. It's this copper that oxidizes in the water. And when copper oxidizes it turns a green color causing your pool to look green.
The algaecide in the kit can cause some foam if there is no algae in the pool to destroy – it lingers around with nothing to kill. Spring time algaecides use surfactants to work and these molecules can react with agitation to cause froth.
It is best to wait 30 minutes after adding it to your pool. We recommend waiting at least 15 minutes to swim after adding algaecide to your swimming pool. Most algaecides are perfectly safe to swim with. It is not recommended to swim with flocculent in your pool as it will reduce its effectiveness.
So unless you're dealing with mustard algae or black algae, leave the algaecide on the shelf and get ready to shock the heck out of your pool. But when dealing with regular ol' green pool algae, chlorine is your best bet to kill it dead.
Algaecides treat and prevent pool algae, but not all algaecides are created equal. To treat green pool water, ensure you select an algaecide that kills green pool algae. After treatment, some dead algae may remain in your pool. Continue to thoroughly brush your pool's surfaces often.
pH Balance and Chlorine
Algaecides do not directly affect the pH balance in your pool, but too much algae will raise the pH level. By eliminating algae, the algaecide helps return pH levels to normal. Algaecide also works together with chlorine, helping the chlorine to be more effective against algae and bacteria.
Add pool algaecide at a rate of 12 ounces per 5,000 gallons of pool water.
Shock and Chlorinate Your Pool
Shocking kills any bacteria that might linger in your pool during the winter. We recommend shocking a few days before you close the pool. If that is not possible, make sure to shock the pool the night before you close it for winter.