3/4" FHT connections fit most washing machines - available with 90° elbow if needed for tighter spaces to help prevent kinking.
¾-Inch Fittings
Most washing machines and home water connections in the U.S. use this size, ensuring compatibility. This fitting size also allows for a higher water flow capacity and better water pressure compared to smaller fittings.
3/4 inch BSP threaded connection (standard washing machine hose thread).
Washing Machine Hose Connections
Most washing machine hoses use standard ¾-inch fittings, but you can choose between straight ends or a 90° elbow design. 90° Elbow Fittings: Ideal for tight spaces, as they reduce strain and prevent kinking.
Diameter Outer: 15mm. 3/4''- 2.5m.
The most widely used for pressure washer hoses are 3/8-inch fittings. 1/4 inch: Used for smaller pressure washers and accessories. 3/8 inch: The most common size for residential and commercial pressure washers. 1/2 inch: Used for high-flow applications or larger pressure washers.
Drain hoses for domestic washing machines and dishwasher's are generally universal but the end fitting that connects to the machine sometimes differ. there are a number of differing “cuff” diameters (19mm and 22mm) but these can often be purchased separately and fitted to a length of hose.
As mentioned earlier, you can always identify AN fittings based on the male thread size (outside diameter). These sizes are constant regardless of brand, hose type, or fitting configuration. If your fitting has a convex 37 degree flare at the end, the threads will tell you the AN size (and vice-versa).
Do new washing machines use the same hoses and plumbing? All washing machines should use standard sizes and fittings. But there are variances in design across different manufacturers and a few potential problems as discussed in this article. You will always get new fill hoses with a new washing machine.
Hose diameters range from 3/8 inch, 1/2 inch and 3/4 inch. The bigger the diameter, the more water is delivered. The most common garden hose thread size is 3/4 inch.
3/4 inch BSP threaded connection (standard washing machine hose thread).
First measure the port hole diameter using a caliper. Next, measure the longest bolt hole spacing from center to center or measure the flange head diameter. Most fluid pipe and tube sizes in the United States are identified by dash numbers, abbreviations that make ordering components easier.
Are all washer dryer hookups the same? No. Some have a single handle to allow the water to flow into the washing machine; some will have two separate handles on the valves. But in both cases they should accommodate standard hoses.
Available in a twin pack for added value, these BOSTON Washing Machine and Dishwasher Inlet hoses are both 1.2 metres long, premium quality hoses, fitted with nuts on both ends, suited to 3/4″ BSP threads – the most commonly used size for Australian appliances.
Regardless of their condition, washing machine hoses should be replaced about every 5 years to prevent a flooding emergency. Standard washing machine hoses are made of black rubber. Unfortunately, these hoses only last a few years and will eventually fail, causing one big mess and costly water damage.
The water line size for a residential home is usually a ¾” to 1” diameter pipe. But there are 3 main factors that determine the correct water supply line size, which is also referred to as the water service line.
The drain pipe should be a minimum of 1-1/2" I.D. (inside diameter) to ensure proper draining. The Washer drain hose is a 1-1/4" O.D. (outside diameter). To be confident that no siphoning of water will take place, the drain plumbing must be a minimum of 30" high for Top Load Washers.
To help choose the right size, you will need to measure your bust, waist and hip. Use a tape measure over your underwear or form fitting clothing and compare your body measurements with those on our size chart, choosing the size that closest matches your measurements.
Hoses are measured by inside diameter, and tubes are measured in outside diameter.
Washing machines have 3 hoses: one for hot water, one for cold water, and one is a drain hose. This means there are 3 hoses that have the potential to burst or leak.
Garden hose threads are also used on all watering tools like sprinklers and spray nozzles, so it doesn't matter what brand of garden hose, hose reel, or watering tool you own, all can connect to each other because they all use standard garden hose threads.
22-30mm Worm Drive Hose Clip / Clamp
This worm drive hose clip is made from steel and adjusts from 22mm to 30mm. This size usually suits washing machine waste hoses.