5. Can I Use Algaecide to Clear Cloudy Pool Water? You can use an algaecide to kill early stages of green algae that might make your water appear cloudy, but the best method of getting rid of algae is to scrub and clean your pool using a large leaf net, vacuum, and kill algae with liquid chlorine shock.
If you already have visible algae growth, you'll need to get rid of your algae problem before you treat your cloudy pool water. Unfortunately, algaecide won't solve the problem. It's better as a preventative measure, not a treatment. To remove algae, you'll need to skim, brush, and vacuum your pool.
It could take up to 24 hours for the pool water to clear after treating with Algaecide. We suggest waiting at least 48-72 hours before adding any more items (shock, algaecide, etc) to your pool water. If there are no signs of clearing you may need to shock your pool or drain and refill with fresh water.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
Weekly bottom and side pool brushing to discourage algae and dirt build-up. Weekly filter check for de-clumping. Testing the water for pH, chlorine, calcium and other chemical balances. Using the vacuum cleaner – in the case of an above-ground pool.
It's usually just a temporary reaction as the sanitizer works its magic, and doesn't always indicate a problem. But if the cloudy water persists long after you've shocked the pool, you're likely having an issue with water balance, circulation, or filtration.
Cloudy or milky swimming pool water is caused by seven main issues: improper levels of chlorine, imbalanced pH and alkalinity, very high calcium hardness (CH) levels, faulty or clogged filter, early stages of algae, ammonia, and debris.
Now is the time to add Pool Clarifier and let it circulate for 12 hours. This will clump the algae together into vaccumable pieces. Shut your pump off and let the cloudiness settle. This may take up to a few days for very cloudy pools.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
Cloudy water may still be safe to swim in, but if the chemicals are not balanced, then swimmers can experience red eyes, irritated skin, and rashes. If the cause is environmental factors, it can usually be cleared up with a clarifier and regular cleaning.
To treat pool water made cloudy by a lack of chlorine, simply keep adding chlorine to the water until the water maintains a chlorine residual of 2ppm or more. If you suspect that the cloudiness is caused by poor water balance, simply add a pH/alkalinity decreasing chemical until the water comes into balance.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
Baking Soda
Most remedies call for adding additional chlorine into the water. If your water's pH balance is between 7.2 and 7.5, however, you can add baking soda to the water to help clear it up. This serves as a replacement for chlorine because baking soda is a natural cleaning agent.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
When closing and winterizing your pool, it is important to remember to balance your pool water's chemistry prior to closing and don't forget the algaecide. Algaecide is simple and effective with one quart of winter algaecide typically enough to treat 20,000 gallons of water all winter long.
It is best to wait 30 minutes after adding it to your pool. We recommend waiting at least 15 minutes to swim after adding algaecide to your swimming pool. Most algaecides are perfectly safe to swim with. It is not recommended to swim with flocculent in your pool as it will reduce its effectiveness.
There are a few different types of algaecides that contain various chemicals to suppress and fight off algae. Many of them include copper or copper sulfate. It's this copper that oxidizes in the water. And when copper oxidizes it turns a green color causing your pool to look green.
So unless you're dealing with mustard algae or black algae, leave the algaecide on the shelf and get ready to shock the heck out of your pool. But when dealing with regular ol' green pool algae, chlorine is your best bet to kill it dead.
When the pH levels are imbalanced, it renders the free chlorine ineffective and the levels decrease. Too little free chlorine forms chloramine and it is this combined chlorine that results in your pool's cloudy appearance.
Adding a recommended dose of shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
In most cases, a cloudy pool after shocking is only temporary and should clear up within 24 hours. Keep filtering your pool, add a little clarifier to help, and your pool should be clear in no time. If after 24 hours your pool is not clear, then you may need to look a little deeper for the solution.