Where 36'' is a common width for a sink cabinet, the typical measurement here is going to be 24''. You should have roughly 24'' from front to back to work with, which will be enough space for any standard sink. It's unlikely that you run into trouble with this dimension, but it's good to double-check just in case.
Base cabinet size
To determine the maximum sink size for your base cabinet, measure the interior of your cabinet and subtract two to three inches from each dimension. A 36″ base cabinet can handle a 33″ sink at most; a 30″ cabinet should be fitted with a sink no larger than 27″ wide.
The most common sink sizes for a 30-inch cabinet are 24 to 27 inches wide. These sizes offer a comfortable fit within the cabinet and provide enough room for daily use.
TIP: Standard cabinet sizes are in 3” increments. I.E.: 27”, 30”, 33”, 36”, etc. In general your sink should be at least 2-3” smaller than your cabinet size.
Measure the opening width under your existing sink (or where the new one will be installed) from left to right. This measurement is your cabinet size. Then, allow at least 2-3 inches on both sides for mounting hardware. For example, a 36" cabinet can accomodate a 30-32" sink.
Another larger option, that provides more variety in its use is a 29" double bowl sink. This sink will fit in your 30" kitchen sink base cabinet and provide you with two 16x13"basins.
You need a 36" cabinet. A 33" cabinet will only fit a 30" sink.
The recommended size for a 36" base cabinet is a 33" farmhouse sink or smaller. It is recommended that your base cabinet be 3 inches larger than the size of the farmhouse sink you are considering to install.
Wondering why you can't fit a 36” sink in a 36” cabinet? That's because of how the sink attaches to the counter! Every undermount sink has a bit of a lip that gets siliconed to the underside of the counter – reinforced with metal clips. That lip and those clips take up an inch or two (and vary from sink to sink)!
A 36" sink will fit into a 36" cabinet easily if you strap it in place. Manufacturer's allow for chubby plumber fingers to access clips to tighten. If you eliminate the clips, you eliminate the need for access.
Yes, you definitely can! Something you should keep in mind, though, is you'll have to cut out the front of the cabinet and remove the counter top prior to farm sink installation. If you want to make the job easier, consider getting a retrofit farmhouse sink, which is meant for a standard kitchen sink base.
Kitchen Cabinet Kings
General rule of thumb is actual sink should be 3" in actual width less than the sink base for smooth fit. However if you notch the sides of the cabinet, you should be able to get something as tight as 1.5 less than cabinet to fit.
Start by measuring the depth of your cabinet. Place your tape measure along the bottom of the cabinet and measure from the back to the front edge. Next, measure the total width. Place your tape measure along the bottom of the cabinet to measure from the left edge to the right edge.
No matter what you do, you will most likely need a special or custom cabinet to accommodate your new farmhouse or apron sink. This is because there are many styles of sink designs and how they need to be installed, typically requires a non-standard cabinet. The two most common types are Drop-in or Undermount.
For Frameless, cabinet sides are usually 3/4'' plywood each. So a sink 25.5'' and narrower would fit. For framed usually the face frame is 1.5'' on each side, so if you want to go farmhouse, you'll probably have to go for a 24'' sink to fit perfectly or I guess you can cut into the frame.
The standard sink size is about 22 inches long to 30 inches wide, but once again it's crucial to take proper measurements. If you're replacing a drop-in sink with rims, start measuring from the outer lip of the sink, not the basin itself.
Standard-sized kitchen sinks measure 22 inches by 30 inches.
While the front-to-back measurement of the sink typically remains the same (roughly 22 inches) due to the size of most cabinets, the length of various kitchen sinks can vary immensely.
Sink Landing Counter Space
The landing space requirement at a main sink is 24″ on one side and 18″ on the other side. The countertop landing area beside the main sink helps with Clean-up duties. With the dishwasher typically places on one side of the main sink the 24″ landing counter is taken care of.
The most common sizes for a kitchen sink are 30" or 33", however a standard size could measure anywhere between 24" and 36" in length.
They, therefore, require a special cabinet configuration, but it's entirely possible to convert an existing drop-in setup to accommodate a farmhouse sink. You'll want to choose a sink that is a few inches smaller in width than the cabinet so that there is cabinet trim on either side of the sink.
When selecting, or designing, a base cabinet for your new farmhouse sink, it is important that the size of the base cabinet is correct. Your base cabinet should measure 3" longer in length than the sink you are installing. For example, if you have a base cabinet that measures 36" wide it will support a 33" sink.
A good place to start when looking for the right size is with the most popular sizes for farmhouse sinks, small, medium, and large. Or the most common, either a 30″ or 33″ single bowl.
The standard size for a kitchen sink can vary, but a typical size for a single-bowl sink is around 30 to 33 inches in width and 20 to 22 inches in depth. Double-bowl sinks can range from 30 to 48 inches in width, depending on the bowl size and configuration.
Double Basin/Bowl Sink
The most popular type of kitchen sink arrangement, dual basins allow for washing on one side and rinsing or drying on the other side.
Besides, in order to avoid backsplash spots at the bottom of the upper cabinet, please leave more space between the upper cabinet and the sink. Usually, the upper cabinets should be at least 12 inches above the sink.