Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
If anything could be considered “normal”, it would be about 10 psi. Most filter systems are designed to operate in the 5-15 or 10-20 psi range. The way to find out your particular correct pool filter pressure is to clean or backwash the filter thoroughly and empty the pump and skimmer baskets.
Generally, if your pool filter water pressure rises more than 10 PSI over the normal range, it's time to clean – or possibly even replace -- your filter. For most filters, 20 or 30 PSI is considered too high, but you should consult your pool professional to make sure that's true for your model.
Normal pressure for most pools is between 10 and 25 PSI (70-170 kPa). The pressure for filtration systems varies depending on the type of filter, the size of the lines, the pump and other pool equipment.
High swimming pool filter pressure is usually the result of a lot of particles being filtered out of the swimming pool water. When pressure rises it is time to backwash the filter if you have that option with a sand or diatomacesous earth (DE) filter.
The pressure gauge should read approximately 50 - 70 kpa when the filter is clean. Backwashing is indicated when the pressure exceeds 70 kpa.
The jets should all point in the same direction, ideally at a 45-degree angle that's directed toward the bottom of the pool. One way to remember it: Point the jets at 4 o'clock or 7 o'clock and ensure that the jets are not pushing water toward the skimmers.
The best way to position your pool jets is angled slightly downward and all pointing at the same direction or depending on the shape of your pool, that will create one “flow” or circular motion in your pool. The direction should be away from the skimmers.
It's good practice to point your return jets in a direction that will circulate the water in your pool. If your pool only has one jet, point the jet toward the skimmer and downward. This will circulate the water, and push the water at the bottom of the pool to the surface.
The level at which pool skimmers function properly is between one third and about half way up the opening of the pool skimmer. If the water level is too high the debris floating next to the opening may pass by without being pulled into the skimmer.
The first thing to do to increase the suction is to check for blockage and air leaks. If one of the skimmers does not suck, it would be necessary to remove the basket from the skimmer. Then check if there isn't a flow control valve at the bottom of the skimmer, which would be almost closed.
Zero pressure means that there's nothing going on inside of your filter, so simply check if the valves leading to your filter are in the correct positions. If everything seems to be running correctly, pump is okay, water flow and everything, then give your pressure gauge a few taps, it could just be stuck.
Add diatomaceous earth (DE) to your pool skimmer, stick to around a scoop or two – no more than the size of a 1lb coffee cup. The moment you do this, go to the pool jets to see if it is returning DE into the pool, or if the water suddenly looks cloudy. If it is, you likely have an issue with your filter.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
The most common reason for weak jets is an air leak. An air leak would come from the suction side of the system. This would be the area between the skimmer and the pump. One way to determine if you have an air leak is by looking for air bubbles coming out of the return jets.
It could be a clogged pump basket, impeller, pipe, or skimmer basket. It could also be a closed or broken valve before the pump. In some cases, the pump may have an air leak and is drawing in more air than water. This can reduce filter pressure (and filtration ability).
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool's size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool's turnover rate is.
It is recommended you have your water level between one-third and one-half up the swimming pool skimmer box opening. If the level is higher than that, it may slow or even stop debris from being pulled into the skimmer box through the plate or valve.
The skimmer is also a resting place for larger pieces of dirt and debris that are blocked by a skimmer basket. For effective filter action, the water level should be at the midpoint of the skimmer. Too low, and water cannot flow into the filter system at all; too high and the flow will be less efficient.
When working correctly, pool pumps should be completely full of water. In this guide, we discuss different tips on how to diagnose and correct the issue of a pump that is not filling up all the way. Note: This guide is meant for pool owners who are used to seeing a full pump and a half-empty pump is out of the norm.
Air bubbles occur when the pool's suction system pulls in the air instead of water from your swimming pool. The air gets into your system before the point where water enters the filter; that is to say, at the skimmer, pump, or the unions.
Though returns have traditionally been placed 12 to 18 inches below the water's surface, more professionals are recommending that they be installed closer to the floor.