They're called headwalls and sidewalls. A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.
Eaves. The eaves of a roof is its lowest horizontal edge. The eaves may terminate flush with the outer face of the wall, in which case it is known as a 'flush eaves'. It may also project out beyond the external wall, with a soffit below.
The eaves are the edges of the roof that hang over or beyond the vertical walls of a building. Their main purpose is to direct water away from the building itself. Eaves can have decorative or architectural elements!
There are two commonly used methods of roof-to-wall connections. Wraps: These are steel straps that are installed over the tops of trusses and anchored to wall along the side of the truss. Clips: These are steel straps that are attached to the sides, rather than the tops, of the trusses.
The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.
A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.
Coving and Cornice are not just used for decorative purposes, but also serve as a functional product. This is because they can hide pipes and wires whilst also serving their main function as distinguishing the difference between the wall and the ceiling.
The connection of the roof framing to the walls must be strong enough to resist wind pressures that try to pull the roof up and away from the house. Typically, roof rafters or roof trusses are connected to the wall using nails driven at an angle through rafters or trusses into wood wall top plates or beams.
A cornice is a type of moulding which runs along the top lengths of your interior walls, which sits in the join between the walls and the ceiling. Cornices are also commonly known as coving, or crown, bed or cove moulding.
Lead flashing is a piece of milled lead that sits between joints to create a durable and weathertight seal. Lead flashing has been used for hundreds of years in situations such as where a roof meets a wall, on a roof valley, around other penetrations such as chimneys, pipes, and around window and door openings.
The cornice area is where walls and ceilings join.
Cornice: a generic term used to describe any decorative moulding that conceals the join between wall and ceiling. Coving: a particular form of cornice that is uniform when looked at from a side-profile perspective.
The soffit is the exposed board under the overhanging eaves of your roof that goes under the fascia board. Soffits protect your roofing system from the elements by forming a barrier between your roof system and the elements.
A gable is the section of the wall located at the end of a pitched roof. They have two sloping sides that come together at a ridge. It will be on the opposite side as the eaves and is also referred to as a rake.
Soffit is the material that lines the underside of your roofing on an overhang and can be either vented to help air flow or closed to protect the interior. Fascia is the forward-facing trim that lines the perimeter of the roof and is perpendicular to the soffit. Its primary purpose is protection of the roofing.
There should be small gaps between your roof and the walls of your home, and other buildings. These small gaps let building materials shift, expand, and contract with weather and other outside forces, and they prevent moisture from wicking down walls from roofing and gutter systems.
Ceiling moulding, also known as crown moulding or cornice, runs along the top of a room where the wall meets the ceiling. It softens the transition from wall to ceiling. Crown moulding can be simple or intricately detailed. These types of moulding trim can make a room look polished.
Method #1: Using Caulk
This method is the most time consuming, but it creates a very crisp, even line where the ceiling and wall meet. It's the best way to touch up an already-painted room.
An attic (sometimes referred to as a loft) is a space found directly below the pitched roof of a house or other building.
Hangers and clips for connecting roof trusses to timber and masonry.
Headwall Flashing
Headwall Flashing is a bent piece of flashing installed behind the siding of a vertical surface and over a course of shingles. Also called “L” flashing, headwall flashing receives its name based on where it gets installed. A headwall is the junction of a roof plane and a wall.
The In-Between: Meet the Attic
That space is called the attic.
Cornices. Cornices are the mouldings that sit where walls meet ceilings. They are often ornate and decorative.
Coving Curved junction between wall and ceiling ie.
Cornice — A decorative moulding or trim installed where the wall meets the ceiling. It adds a decorative touch to the room. Crown Molding — A specific type of cornice, characterized by its decorative, often ornate design.