Usually, hosing them down once a month is sufficient. Use soap and water, if the pavers are still dirty after sweeping and water hosing, make a solution of soap and water. You can use dish soap, laundry detergent, or any type of general-purpose cleaner. Never use bleach on your pavers, as it can damage the surface.
There are useful tools for cleaning paving stones, such as joint scrapers, sweepers, and pressure washers. In addition, pavers can be cleaned with a small pickaxe, broom, and garden hose.
Dilute white vinegar with water in a bucket, at Walmart (a 50:50 solution is fine), and apply this natural, eco-friendly cleaning solution to the paving slabs with a firm brush and rinse thoroughly.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Cleaning your pavers with bleach has a lot of benefits: Disinfecting the Surface: Bleach is an effective disinfectant and can kill any bacteria or mold on the surface. This will help to prevent any health hazards from occurring. Removing Tough Stains: Bleach is also effective in removing tough stains from the surface.
You can use a pressure washer on your patio pavers if you want to clean stubborn stains or mildew from them. However, be very careful when doing this! Use a gentle spray and avoid letting the water run down the sides of your pavers, especially if they're set in the sand rather than mortar.
Apply the Simple Green solution. Allow the product to soak for a minute or so on heavy soils and greasy spills. Scrub, if necessary. Scrubbing with a soft bristle brush or non-abrasive scrubbing pad provides agitation that will help to loosen soils and will ensure a thoroughly clean, residue free surface.
The simplest path to reviving tired pavers is to apply an acrylic-based semitransparent concrete stain, such as Behr Premium Semi-transparent Concrete Stain ($27/gal.; Home Depot) or Valspar Semi-transparent Concrete Stain ($28/gal.; Lowe's).
Baking soda has low-abrasive properties, making it an excellent cleaning material for stuck-on grime and tough stains. Additionally, baking soda is absorbent, allowing it to absorb oils from the surface of the pavers, especially freshly oil spill on concrete pavers.
OxiClean is a powerful concrete cleaner that works well on various materials, including pavement and grout. This concentrated solution provides excellent cleaning without leaving residue.
'A homemade cleaning solution for your patio can be made by mixing equal parts water and white vinegar,' says Zak. 'This natural cleaner is effective in removing dirt, mildew, and algae. For stubborn stains, you can add a few drops of liquid dish soap to the mixture.
Depending on the material of the paver (non-coloured concrete is safe), CLR may be suitable. Always spot test in an inconspicuous area first. Make sure the pavers are not coloured, stamped, sealed or coated.
Whether your patio is sealed concrete or cement, or even sealed concrete pavers, a bleach and water solution makes it easy to clean away built up soil, stains from leaves and pollen, mold, mildew and algae.
Use Vinegar or Bleach
If you are going to try this approach to remove mold or algae, first try a mixture of white vinegar and water to spray down the area and kill the mold.
In fact, vinegar removes mold from concrete better than bleach. Bleach will only remove the top layer of mold, causing the mold to return.
Using a dish soap solution and a toothbrush, carefully scrub at stained areas. Spray off the soap with a power sprayer, and let the wall dry. * If you are cleaning concrete blocks and soap does not remove the stains or dirt, fill your garden sprayer attachment with bleach.