Pool heaters have an average life expectancy of 6 to 12 years. But if you use them properly, keep them well-maintained, and make sure that the pool has balanced water chemistry, you can help them last longer than expected.
7-10 years is the average life expectancy of a pool heater.
The best way to keep your pool heater in top shape is by getting a maintenance check-up at least once a season. The cost of maintaining your pool heater will be minimal compared to the costs of having to replace it before its time!
When this happens, calcium deposits build up inside the tubes over time. As a result, it is harder for water to pass through the heat exchanger freely, leading to clogging and the heater will not fire (for safety reasons) and causes the heater to fail.
Lifespan of Commercial Application Pool Heaters:
Two major manufacturers of pool heaters stated that the typically life expectancy of one of these units is around 5 years. This shorter life span is due to a number of reasons.
On average, pool pumps last eight to 12 years before needing replacement. Over time, it's normal for pool parts to begin to wear down. In addition, swimming pool technology has come a long way in the last decade.
In general, the sun will make it easier for your pool heat pump to do its job. Regular exposure to direct sunlight will keep your heater warm, meaning that it will need to exert less power to warm up the rest of your pool. Solar-powered pool heat pumps also thrive when exposed to consistent sunlight.
Swimming pool heaters are one of the most complicated pieces of pool equipment and we recommend calling a local professional to make repairs. However, there are a few common problems you can diagnose yourself.
If the pilot won't light, the gas pressure could be low, the air supply may be poor, or the heater may not be venting properly. Check the gas pressure, and adjust it if necessary. Then check all the vents to make sure they're not blocked. If any of them are, simply remove the blockage, and try lighting the pilot again.
A dirty filter can cause low pressure and as a result, cause the heater's pressure switch to turn OFF. A dirty filter can prevent a heater from firing and it can also cause your heater to shut off before warming the water to the desired temperature.
Maintenance. Your pool heater should be scheduled at least once a year for maintenance, and can benefit from bi-annual maintenance. During a maintenance appointment, your pool heater will be thoroughly inspected, components will be cleaned, lubricated and adjusted, and the unit will be tested for safety and performance ...
Check The Filter
Pool heaters rely on a steady stream of water in order to operate properly, and when this is interrupted, you will start to run into issues. To make sure that your pool heater is getting enough water, you need to check your filter.
Remove the heater screws that secure the heat exchanger in place; move it to a clean surface. Apply a degreaser to the heat exchanger using a soft-tipped brush. Allow the degreaser time to loosen any soot. Wash the heat exchanger with a garden hose.
Calculate the pool surface area in square feet by multiplying the length and the width of your pool. Then, use this formula to figure out the BTUs you'll need your heater to put out: pool area (sq. ft.) x temperature rise x 12.
HOW LONG WILL THE TANK LAST? 100 gallons of propane will last approximately 25 - 30 hours of run time.
Check the Power: If your Raypak pool heater isn't working at all, the problem could be something as simple as a lack of power. Go make sure there aren't any tripped circuit breakers in the fuse box, then check that the unit's time clock is set to the “On” position.
The most common cause of a heater that cycles on and off could be inadequate water flow to a dirty filter or closed valve. (See information on How to Backwash a DE Filter or Clean a Cartridge Filter).
Reset the circuit breaker by turning the circuit breaker off and then back on. Wait five minutes for the Rheem pool heater to power back on and the "Power" light on the control panel to illuminate.
The FLO code is indicating that the filter pump has stopped the flow of water to your heat pump. The heat pump cannot heat without water flow so it will turn itself off until the filter pump timer turns back on giving the heat pump the water flow it needs.
A pool heat pump should not be left running all the time. For one, you are wasting electricity by keeping it on when your pool is already warm enough. Also, this will lead to an increase in energy costs month after month.
It depends on a few things to determine how long it takes a heat pump to heat a pool. However, overall a heat pump generally heats a pool after 24 to 72 hours by 20-degrees Fahrenheit. For smaller pools like a spa pool, the heat pump can heat a pool between 45 and 60 minutes.
On average, pool pump replacement costs about $440, average prices ranged from $80 to $800 for pool pump replacement in the US in 2020.
Overheating. For safety reasons, many pool pumps are designed to shut off automatically if they begin to overheat. The mechanisms that perform this task are known as thermal overload switches. If your pump continues to shut off, it could mean that the thermal overload switches are going bad.