Algaecide will kill the algae and mold affecting your pool water, but it is best used as an algae preventative. While it does not change the pH balance of your pool water, it will keep algae from growing and work with your chlorine sanitizer to keep those levels balanced.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
Algaecides can kill algae spores in your pool, but they are even more effective at prevention. Use an algaecide once a week 12 to 16 hours after each shock treatment to protect your pool and keep your water crystal clear.
Now is the time to add Pool Clarifier and let it circulate for 12 hours. This will clump the algae together into vaccumable pieces. Shut your pump off and let the cloudiness settle. This may take up to a few days for very cloudy pools.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
So unless you're dealing with mustard algae or black algae, leave the algaecide on the shelf and get ready to shock the heck out of your pool. But when dealing with regular ol' green pool algae, chlorine is your best bet to kill it dead.
It is best to wait 30 minutes after adding it to your pool. We recommend waiting at least 15 minutes to swim after adding algaecide to your swimming pool. Most algaecides are perfectly safe to swim with. It is not recommended to swim with flocculent in your pool as it will reduce its effectiveness.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Regular algaecides do not contain copper, but rather quaternary ammonium compounds, also known as "quats" or "polyquats." These compounds are safe for immediate swimming. Use of too much algaecide may cause slight eye or skin irritation, so always be sure to follow the manufacturer's instructions.
Your chlorine levels won't return to normal right after you shock your pool anyway, so we recommend waiting at least 24 hours to add algaecide. When adding algaecide to your pool, make sure you add the correct amount.
The algaecide in the kit can cause some foam if there is no algae in the pool to destroy – it lingers around with nothing to kill. Spring time algaecides use surfactants to work and these molecules can react with agitation to cause froth.
Algaecides treat and prevent pool algae, but not all algaecides are created equal. To treat green pool water, ensure you select an algaecide that kills green pool algae. After treatment, some dead algae may remain in your pool. Continue to thoroughly brush your pool's surfaces often.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
All algaecides work by releasing positive-charged ions into the water, which combine with the negatively charged algae particles. Algaecides don't break down in sunlight the way chlorine does, so they remain available much longer.
pH Balance and Chlorine
Algaecides do not directly affect the pH balance in your pool, but too much algae will raise the pH level. By eliminating algae, the algaecide helps return pH levels to normal. Algaecide also works together with chlorine, helping the chlorine to be more effective against algae and bacteria.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Grab a brush and some baking soda. Bicarbonate, the active ingredient in baking soda, is an effective spot treatment to help kill the algae and loosen it from the wall. Make sure you really get every last particle free; black algae has particularly long and stubborn roots which makes it a persistent strand.
Shock the pool with chlorine every day until all the green is gone (possibly 3 to 4 days). 2. Run the filter 24 hours a day and backwash every day until the green and then cloudiness is gone (usually up to 7 days, sometimes as long as 2 weeks depending on the filter). 3.
You can get rid of algae quickly by vacuuming and brushing your pool, balancing your pool's water chemistry, and then shocking and filtering your pool water. Just be thorough as you clean your pool surfaces. If you leave behind even a small number of algae spores, it won't be long before they regrow and bloom again.
Foaming in a pool means there are high levels of total dissolved solids (TDS) in the water. TDS are the measure of solid matter that has liquefied. Foreign solids like oil, soil, and dirt dissolve in pools. High levels of TDS makes pool water look cloudy and can even make it taste salty.
The most common cause for swimming pool foam is a high organic load that causes the water to thicken. With “thick” water, this means that the surface tension is stronger and bubbles caused by your return jets tend to hang around longer, causing foam.
It could take up to 24 hours for the pool water to clear after treating with Algaecide. We suggest waiting at least 48-72 hours before adding any more items (shock, algaecide, etc) to your pool water. If there are no signs of clearing you may need to shock your pool or drain and refill with fresh water.