If you suspect your toilet keeps running because of a major leak or damage to the bowl, gasket, flushing mechanism, or pipes, call a plumber right away. Be wary of easy, DIY solutions that might make problems worse, costing you more time, stress, and money in the long run.
Due to the large amount of wasted water, a running toilet can cause your utility bills to skyrocket. It's best, then, to have your toilet examined by a plumbing expert as soon as possible. The longer you avoid tackling the issue, the more expensive it can become.
Leaking toilets are more than just an annoyance—they waste water which leads to higher water bills. The next time you hear the unmistakable sound of a running toilet, it's a sign of a leak in need of immediate repair. The good news is that sometimes diagnosing and fixing the issue can be a simple and inexpensive task.
Beyond the astronomical water bills running toilets have the power to produce, they can also cause damage to the home if water is actually leaking out of the bowl or tank.
If the water is overflowing or close to the rim of the toilet bowl while the water is running, or after you have fixed what you thought was wrong, you may want to turn off the water valve to the toilet and call a plumber.
A continuously running toilet can waste up to 200 gallons a day or more depending on the volume flow down the drain. This can cause a terrible increase to a family's typical water use, so fix toilet leaks as soon as possible. Some leaks are easy to find, such as a dripping faucet or running toilet.
According to Fixr, the average toilet valve repair cost is between $75 and $200 to replace a flush valve or up to $400 to fix a constantly running toilet. This includes the cost of the plumber's time for the toilet repair and the cost of the toilet parts.
Typically, a running water toilet will waste thousands of gallons of water per month which translates to approximately $200 unnecessarily tacked onto your monthly water bill-- that's nearly $2,500 dollars a year down your toilet bowl. The above scenario is in the case of an extreme toilet leak.
Your toilet may be constantly running because of a faulty flapper seal. One of the most common causes of a flapper seal breaking is improper installation. Human error is often to blame for this issue, but some design flaws in older toilets can cause the same problem.
Running noises when no one flushes could mean a variety of things: The valve in the tank allows water to escape into the bowl. The flapper chain in the tank is too tight and prevents the valve from shutting all the way. The float in the toilet tank is set to a high mark, causing the toilet to run constantly.
The steady flow of water from a leaky toilet or faucet day and night can quickly flood your septic tank as well as the ground around the drain field, making it impossible for water to flow out of your septic system, eventually leading to septic system failure. This is referred to as hydraulic overloading.
When water continues running from the tank to the bowl, that's not a good sign. Other than the irritating noise, a running toilet wastes water. While a running toilet may not qualify for an immediate replacement, you shouldn't ignore it. Running toilets are usually caused when the flapper valve doesn't seal.
If your toilet is still running after replacing parts or adjusting, a clogged toilet could be the culprit.
In general, a single flush 1.6 gpf or 1.28 gpf toilet tank will take around half minute (30 seconds) to one minute (60 seconds) to fill.
The average leaky toilet can waste about 200 gallons of water per day. That's over 6,000 gallons a month ($70.06*) for just one leaking toilet! Some toilets may produce a running water sound that is easy to hear. Some leaks are visible as a small trickle running from the rim to the water in the bowl.
If the toilet keeps running or runs intermittently, you're not getting a good seal. Try a different flapper if the toilet won't stop running. If you just can't find a flapper that seals, consider replacing the entire toilet overflow tube/flapper. On most toilets (two-piece), this means removing the tank.
Test the Flapper
Push down on the flapper with a stick when you hear the toilet water running and listen for it to stop. If it stops, you know the flapper isn't sealing properly. Replace the toilet flapper immediately.
The toilet's flush valve will typically last 6-7 years. A toilet fill valve might only last four to five years. In general, you should expect to replace the parts in your toilet every so often while keeping the actual bowl in place.
If your toilet randomly runs off and on for a few seconds, it is likely due to a broken flapper. While the flapper is supposed to drop down and re-seal the tank when enough water has gone through, a cracked or decaying flapper will allow water to keep flowing through and run periodically.
A toilet that cuts on and off by itself, or runs intermittently, has a problem that plumbers call a "phantom flush." The cause is a very slow leak from the tank into the bowl. This problem is almost certainly caused by a bad flapper or flapper seat.
According to SFGate, flushing the toilets accounts for a whopping 30% of the average household's water usage. Therefore, reducing the amount of water flushed away every time you visit the bathroom is an effective way to lighten the load on your wallet.
On average, most toilets will have a lifespan of between 10 and 15 years, even with regular use. The lifespan may vary depending on the toilet model and the wear and tear it experiences over the years. Most toilets will start to give you warning signs indicating the time for replacement is near.