Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
SKIMMER NOTES: No. Chlorine and shock are not the same thing.
Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool. Short answer: No.
Liquid chlorine and granular shock have the same active chemical that sanitizes your pool, what changes is the strength and the way you use it. Liquid chlorine is less costly, unstabilized and comes in liquid form. Granular shock is stabilized and comes in a solid form that dissolves in your pool.
Similarities Between Liquid Chlorine & Powdered Shock
Similarly, both forms have a higher concentration of available chlorine than those used in daily chlorination. They also both kill nearly all living microorganisms, bacteria and contaminants with ease.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
"Shocking” refers to the process of adding chlorine or non-chlorine pool chemicals to the water in order to raise the "free chlorine” level. The goal is to raise this level to a point where contaminants such as algae, chloramines and bacteria are destroyed.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool. As a reminder, you want your pH to be between 7.2 and 7.8ppm and your free available chlorine to be 1-4ppm for safe swimming.
The cold water, anything below 65°, has an impact on the ability of the chemicals to dissolve properly. I would recommend using liquid chlorine if you have to shock in lower temperatures. You can dissolve granular shock in warm water. Perhaps it will work if you completely dissolve it before adding it to the pool.
Pools are shocked to keep the water healthy and clean by removing algae and bacteria after heavy bather use or contamination events. In addition, pool shocking is used to eliminate harmful combined chlorine in the water.
BUT, if you have to shock your pool during the day in broad daylight, you can still swim after adding shock. It's recommended that you wait one hour after adding shock with the filter running, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment. Improve filtration with a pool filter cleaner or filter aid like Jack's Filter Fiber.
Q. How long does it take to shock a pool? The actual process shouldn't take more than an hour, but depending on the product used, it could be up to 8 hours before you can use it.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
If the pool is still very cloudy or green, you may need to shock it to make it safe to swim in again. First, make sure that the filter system is working properly and the chemicals are still at the proper levels. Next, mix up your chlorine shock (hyperchlorinate) treatment.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
75 ounces per 3,000 gallons every week. Initially you will need stabilizer to protect the chlorine from the sun. This is added at a rate of one pound per 3,000 gallons of water.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. A proactive, productive and energy-saving maintenance activity is to remove the debris floating on the pool surface with a hand-held skimmer.
So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
You do not need as much pool shock during winter as you normally would to achieve the same effect. The National Institutes of Health found that at normal summer water temperatures, the efficacy of chlorine was 2-3 times less than for water temperatures around 50 degrees.