Applying a sealant can prevent stains and other signs of aging plus it makes it far easier to wash away the dirt, grease, and grime that they're regularly exposed to without leaving behind residual effects. Sealers also offer some degree of moisture resistance.
You're wondering what happens if you don't seal pavers. Your pavers won't disintegrate if you don't seal them, but they'll likely fade much sooner than if you applied sealant. You'll also need to clean them more often, and the stains won't be as easy to remove.
Pavers and joints should be resealed every 3-5 years.
After a new paver installation, or after pressure washing an older paver area and re-sanding, a paver sealer should be applied to waterproof the surface and protect it from outdoor elements.
How Much Does It Cost to Clean and Reseal Pavers per Square Foot? In total, you should expect to pay around $2 per square foot to clean and seal pavers. The price may vary between $1 and $3 per square foot, depending on the sealant and method of cleaning.
Apply Paver Sealant to Enhance Faded Pavers
Once the pavers are dry, you can see what they look like in their clean state. If you're content with the appearance, you could stop there. If you still think they need to be enhanced, you could use paver sealant to bring out the color of faded pavers.
If a white haze appears on sealed pavers, it is less likely that the white spots are efflorescence but rather, water condensation collecting underneath the sealer. Removal is still possible, but a chemical solution is required. If your sealer is oil-based, the fix is to re-emulsify the sealer with Xylene.
The simplest path to reviving tired pavers is to apply an acrylic-based semitransparent concrete stain, such as Behr Premium Semi-transparent Concrete Stain ($27/gal.; Home Depot) or Valspar Semi-transparent Concrete Stain ($28/gal.; Lowe's).
Fall or spring is a great time of the year to seal pavers. Cooler weather allows the sealer to penetrate into the pavers unhindered. Pavers will have an adequate amount of protection for when it's time to seal again. Make sure to keep leaves and other debris off the pavers while they are drying to avoid blemishes.
Your concrete pavers will look better than new. 5 gal. bucket covers approximately 500 sq. ft.
Unlike natural stone pavers, porcelain pavers are fade resistant and don't need sealing. Also, they can stand up to almost anything nature can throw at it. Natural stone pavers, of course, are Nature's decorative flooring. Travertine, slate, and quartzite can create eye-popping floors, each different from the next.
Blotchy and Dark Concrete: Blotchy concrete can result from over application. In order to prevent over application, apply sealers in thin, even coats. If over application does occur, use Xylene to correct the problem.
If the sealer is not cured correctly, water can cause white marks or stains on your pavers and can even be trapped beneath the layer of sealer. It is very important not to walk or drive on sealed pavers at least 24-48 hours after application. A protective sealer enhances the natural color and beauty of your pavers.
Enhanced aesthetic: The paver sealer enhances the curb appeal of your properties and provides perfect finish to the paved areas and at the same time stabilizes the joint sand by locking it in place. It protects the pavement against harmful UV rays and prevents fading.
You can expect a concrete or brick paver patio to last 25 to 45 years, with an average of 35 years. Proper installation is critical and begins with a well-compacted base. Maintenance is also important, such as regular re-application of a surface sealer and repair/replacement of damaged pavers.
The longevity of the overall installation of this paving material is typically higher than that of other materials. The best thing about pavers is that they are designed to last a lifetime. They may develop cracks at some point, but that's not a problem because they can easily be replaced.
Brick pavers absolutely, 100% need to be re-sanded prior to sealing. The sand in the brick paver joints serves MANY integral purposes. Keeps joints stable, pavers level,and fills the void between pavers to keep them from becoming loose and wobbly.
Applying two coats of sealer to a porous paver may look good for a short period of time but the paver will continue to absorb the sealer and within a short time will leave the paver looking dull and often appears to be unsealed.
If your pavers have been sealed, which is a service that we offer, it's a lot easier to maintain and it does slow down mold growth for the simple fact that when your pavers are unsealed, that moisture will sit in the joints and make mold grow. Mold likes damp, dark areas.