Never use Murphy Oil Soap or similar products to damp mop wood or laminated floors. Oil soaps leave a film on floors that dull and damage the finish. Remove the film by mopping with one-half cup distilled white vinegar per gallon of water and a clean terry towel.
Step 3: Dry Floors, If Needed
For a homemade laminate floor cleaner, use a small amount of vinegar mixed with water. Never use wax, acrylic products, or bleach because they can damage the floor's finish.
You should absolutely NOT use Murphy's Oil Soap to clean your wood floors!
ZEP Commercial Hardwood & Laminate Floor Cleaner
This powerful, ready-to-use spray removes scuff marks, stains, dirt, grime, and dust. It also has a quick drying time, restores shine, does not require rinsing, and leaves a fresh yet subtle scent.
For heavy cleaning, dilute 1/2 cup Murphy per gallon. Clean well with wrung-out mop, and mop any excess water. No visible residue, no rinsing required.
In short, the answer is NO.
Murphy's Oil Soap is not entirely safe on wood floors, despite many people saying so. Long term, this product will do more harm than good to your wood floors.
In order to preserve and protect the wear layer, make sure any cleaning product you buy or DIY is safe for laminate flooring. Products that are oil-based, acidic or abrasive can damage the surface. Similarly, never polish or wax your floor. Remember, laminate flooring cannot be refinished if it is damaged.
You can make your own floor cleaner right at home. For regular cleaning, just combine a teaspoon of clear and unscented dish soap with a gallon of hot water.
Pine-Sol® Multi-Surface Cleaner is safe for use on laminate floors. Just choose your favorite scent — we like using Original Pine on laminate floors. Pine-Sol® Multi-Surface Cleaner also comes in other scents, like Lemon Fresh®, Lavender Clean®, Sparkling Wave® and Tropical Flowers™.
When diluted properly, Murphy® Oil Soap Original Formula does not leave a residue. Despite the fact that it is called "oil soap," there is no "free oil" left behind. If you see a residue after applying Murphy® Oil Soap for the first time, it's likely that another cleaner was previously used.
The company continued to be run by the Murphy family for 80 years, when they sold it to Colgate. It is available in a concentrated liquid form which is then mixed with water, as well as pre-diluted form which comes in a trigger spray bottle.
Whether you're cleaning one area or all of your flooring, Murphy® Oil Soap is safe to use on hardwood floors.
An oil-based finish will give your floors an amber hue. If you go this route, you'll need to wait about eight hours until the finish is dry, and expect a moderate scent.
Lightly dampen a microfiber mop and always clean following the grain of the wood and allow the wood to dry completely before walking to prevent spotting. If you live in an area with hard water, damp mop with distilled water. The excessive minerals in hard water can leave the floor finishes looking dull.
Using a two sided bucket method (one side soap, one side rinse) or two buckets, mop with 1/2 cup vinegar with a drop of deter- gent or Murphy's Oil Soap mixed with warm water. The clean vinegar odor will go away shortly after the floor dries.
Scrub your floors with an apple cider vinegar solution for a natural polish. Mix 1⁄4 cup (59 ml) of apple cider vinegar with about 1 US quart (0.95 L) of warm water. Wet a mop in the solution and lightly scrub your floors in the same direction that the planks run.
Yes, the Bona Hardwood Floor Cleaner is safe for your laminate floor. Bona Cleaners are safe for your floor as long as your floor is sealed or finished, and unwaxed or unoiled. Both the Hardwood Floor Cleaner and the Stone, Tile and Laminate Floor Cleaner are pH balanced and leave no dulling or sticky residues behind.