So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.
If Calcium levels are also high, crystalline deposits could form. If Metals like copper and iron are high, shocking the pool can cause a temporary (sometimes permanent) staining. Be sure to test your level of cyanuric acid (stabilizer), and if over 20ppm, add 50% more shock. If over 40 ppm, double the dose.
Shock your pool once a week with Salinity Surge Shock or Salinity Oxidizing Shock. Pool shock works as an added defense against bacteria and contaminants. With Oxidizing shock, you can use your pool after just 15 minutes!
Wait until the shock process is complete, then put in the salt. It'll dissolve right away and be ready for the SWG by the time you get ready to use it.
Yes, a salt water pool has a reduced cost of operation as compared to a traditional chlorinated pool. This cost savings is primarily because chlorine is generated from salt and there is no need to buy chlorine. Additionally, salt water pools require fewer chemicals to keep the water clean and clear.
Turn down the salt cell system. If you've reached the recommended chlorine level for your pool, the shock should last several days, so you can turn down your saltwater pool system—also called salt chlorinators or chlorine generators —for a while.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
To get rid of cloudiness, you will have to do a liquid chlorine shock to raise the level of free chlorine (since the chlorine produced by the generator is not enough; a chlorine generator just assists you in maintaining the level of free chlorine).
The pool pump in a saltwater pool should be run 8 to 12 hours per day on average. In saltwater pools, the pump needs to be on for two reasons. The first is to filter the water. The pump should complete at least one turnover of the pool water to filter it properly.
While green algae are endemic in salt water pools, they are the easiest to kill. Green algae tend to grow during summers when the temperatures can get high. They float freely in the pool, making the water green. You might even see them growing on the bottom of the pool, on the walls, or in the crevices.
Sometimes a saltwater pool's chlorinator isn't creating enough chlorine, and the water can become cloudy or develop algae. When this happens, a bit of chlorine can save the day, said Hunker. You can add extra chlorine to the pool through calcium hypochlorite, sodium hypochlorite, or chlorine tablets.
Adding Shock Directly Into The Pool Water
Don't worry—you can't overshock your pool. But beyond fashion faux pas, adding shock directly to the pool water if you have a vinyl liner can be a disaster. The shock granules will sink the bottom and bleach out your liner.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water.
The slimy feel on your pool walls is an early indication of algae growth. To stop algae growth in its tracks, clean the pool filter first. Before adding any chemicals to the pool, make sure you have a clean filter. Cartridge, sand or diatomaceous earth filters all have their own backwashing methods for cleaning.
Generally, it's recommended to wait about 10 minutes between adding each pool chemical. Some pool chemicals like pool salt and cyanuric acid take longer to dissolve in the pool water. The aim is to avoid strong concentrations of chemicals mixing together.
Insufficient chlorine in your pool
When you add a bag of salt into the water sodium chloride dissolves and splits into two separate parts – sodium and chloride ions. Chloride won't kill algae, it needs to be turned into chlorine to do this.
Add Pool Water Clarifier
After your pool water has circulated and your shock has dissipated, it's time to add your clarifier. Clarifier helps bind tiny particles into bigger particles that your filter can capture.
Brown pool water is often caused by metals (iron) becoming oxidized in the pool water. If you shocked your pool water and it turned brown you probably have metals. Oxidized iron usually turns a brown or rusty color in the water.
You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.