Your concrete pavers will look better than new. 5 gal. bucket covers approximately 500 sq. ft.
Your concrete pavers will look better than new. 1 Gal. covers approximately 200 sq. ft.
Essential Values 5 Gallon Concrete Sealer (Covers 7500 Sq Ft) – Made in USA - Excellent Clear & Wet Sealant Designed for Indoor/Outdoor Surfaces - for Concrete | Driveways | Garages | Basements.
approximately how many sq. ft. will the five gallon can cover ? 350 to 450 square feet per gallon, so 1750 square feet on the low end. Our concrete patio has an acid stain and was sealed with the super diamond clear sealer.
1 coat: 150 - 400 square feet per gallon. 2 coats: 75 - 200 square feet per gallon. Variations in texture and porosity of substrate will affect the coverage and performance of the product.
Coverage should be at least 250 square feet per 5 gallons. For larger areas, pour onto the surface and roll. Apply the next coat as soon as possible, not allowing extended time between if possible. Ensure coating is dry to the touch with no uncured material underneath before moving on to the next coat.
Coverage rate:
Total of 2 coats – average coverage around 50 square feet per gallon (or 5 square yards).
This product is not a stand-alone sealer. 1 Gal. of Zep Floor Sealer covers up to 1500 sq. ft.
One of the best paver sealers is the Siloxa-Tek 8500. It is a penetrating concrete sealer designed to treat a variety of applications with an emphasis on hydrophobicity and reduction of water uptake. It dries completely clear with a natural finish that will not change the look or appearance of the susbtrate.
Driveway Square Footage
Some sealants cost more than others, but they average between $0.06 and $0.38 per square foot. A 500-square-foot driveway typically requires 5 gallons of sealant, which can run between $40 and $165. Keep in mind that the price will double if two coats of sealant are used.
When the sealer is applied too heavily, the air displaced through the surface can't escape, and it forms a bubble in the sealer surface. Concrete sealers are best applied in two thin coats.
Sealer that is applied too heavily or too often will create an impermeable barrier and trap that water vapor beneath it. If enough pressure is created by trapped water vapor, the sealer can delaminate from the concrete surface, and might even take some of the concrete paste with it!
Acrylic Concrete Sealers: Acrylic sealers last 1-3 years before they need to be re-coated. Epoxy Coatings: Epoxy coatings last 5-10 years before they need to be re-coated. Urethane Coatings: Urethane coatings last 5-10 years before they need to be re-coated.
Using a nap roller for sealer application will take several times longer than using a paver sealer sprayer and joint stabilization is difficult to achieve. Spraying is the preferred method of applying water based paver sealers as it allows enough sealer to get into the joints.
EXAMPLE: If you are sealing a traditional driveway that has a broom swept finish and 1000 total square feet to cover, you will need 5 gallons of sealer. You will use 2 ½ gallons for your first coat and the remaining 2 ½ gallons for the second coat to achieve the suggested net coverage of 200 square feet per gallon.
You pressure clean the pavers, re-sand the paver joints and then apply two coats of your favorite paver sealer and the job was complete.
Fall or spring is a great time of the year to seal pavers. Cooler weather allows the sealer to penetrate into the pavers unhindered. Pavers will have an adequate amount of protection for when it's time to seal again. Make sure to keep leaves and other debris off the pavers while they are drying to avoid blemishes.
Choosing to seal your pavers will keep your color consistent and un-faded. Not only does choosing to seal your pavers keep the color untouched, but it can also increase the vibrancy of your colors. One largely agreed upon benefit of sealers is that they limit stains.
Penetrating concrete sealers will typically cover anywhere from 100 – 400 square feet per gallon. Two coats are usually recommended so this will cut the coverage amount in half to 50 – 200 square feet per gallon for 2 coats.
One gallon covers up to 1500 sq ft and dries in about 30 minutes. Zep High-Traffic Floor Finish (sold separately # 61524) contains 20% solids for an exceptionally durable high-gloss shine. Formulated to resist scuff and heel marks as well as prevent slips.
BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 400-500 SQ. FT. PER GALLON.
Simply measure the width and length of your sealcoating area, and multiply it to find how many square feet you are sealing. If it's a small driveway, then you can use a tape measure or measuring wheel.
It's easy to calculate how much sealcoat you need: simply measure the length L in feet and width W in feet of the area you want to seal. Multiply them together to get a total measurement in square feet. Fill in the blank with the total number of square feet and the calculator will return the number of gallons you need.