Yes, but you cannot paint it straight out of the tin. Fresh plaster is porous and will soak up paint like a sponge, leading to peeling, flaking, or a patchy finish. You must wait for it to dry completely and apply a "mist coat" first.
Generally, if you're painting new 'finishing' plaster, you'll want to wait a week or two for it to dry fully. Some specialist plasters, such as lime plaster, can take up to a month to dry. The surroundings make a big difference, too. If your walls are in a well-ventilated room, drying will be quicker.
Here are the most common problems we see when people don't prime plaster before paint: Peeling and cracking – Especially in areas like kitchens or bathrooms. Blotchy finish – Uneven absorption creates dull patches that no topcoat can fully fix.
Mist coat paint is simply watered-down emulsion paint, which acts as your primer. All you need to do is get some white emulsion paint and thin it out with water – it's that easy! Ten parts paint to one part water should work. If you don't fancy watering down your paint you can also use Dulux Sealer for Plaster.
I'd add that new plaster - especially if it's got a glass like finish - should be given a very light rub down with some sand paper (something like 120 or higher grit), and then wiped down to remove any dust before mist coating. Same again after the mist cost has dried. Ready for 2 top coats.
5 Common Plastering Mistakes To Avoid
Yes, Dawn dish soap is effective for most painted walls, especially for removing grease or stains. Its mild formula makes it safe for many paint types. However, you'll want to rinse with plain water afterward to avoid leaving a soapy film on the wall, which can dull the finish over time.
Why does the plaster need to be dry? Applying emulsion to wet plaster means that it may not bond properly and you could find that it peels off your wall. Painting on dried plaster can also cause the paint to dry very fast, leaving you with irregular brush strokes and an uneven finish.
The best primer for new, unpainted plaster is actually a mist coat—a base coat made by thinning standard water-based (emulsion) matte paint. This soaks into the highly porous fresh plaster, sealing it gently while letting the moisture escape so the plaster can cure correctly.
Prepare the wall
Wipe it down with a damp cloth and let it dry. If any bits of plaster are rough or raised, lightly sand them with fine-grit sandpaper. This gives you a smoother finish and helps paint stick better. Pay attention to corners or edges that may need extra sanding.
Use KILZ STANDARD Primer on almost all interior surfaces including wood, drywall, plaster, brick, masonry and more. Not recommended for flooring, glossy surfaces, mold and mildew prone surfaces or for stainblocking.
Lath and plaster was a skilled craft and a time-consuming technique and the advent of cheaper, mass produced, pre-manufactured plasterboard meant lath and plaster largely fell out of favour by the 1930s and 1940s. Plasterboard was simply faster and less expensive to install.
10 Mistakes to Avoid While Painting your Homes!
Red is universally considered the hardest paint color to cover. Vibrant red pigments are highly transparent and inherently prone to bleeding through subsequent layers. Other notoriously difficult colors to cover include black, dark blue, dark green, and bright yellow.
The best paint for plaster walls is high-quality acrylic latex or a mineral/breathable paint, finished in a matte or eggshell sheen to hide imperfections. Plaster requires products that allow moisture to breathe and flex slightly. Crucially, plaster needs a proper primer—do not use "paint-and-primer-in-one" products.
Without the mist coat you're likely to have very poor adhesion between your paint and your plaster and quite often it will crack, flake or even peel off in sheets in some instances!
If it's fresh plaster it's pretty much ready to go, mix up your mist coat or your plaster primer and apply a single coat.
Sealing new, bare plaster (often called a "mist coat") is a crucial step. Without it, the highly porous plaster will rapidly suck the moisture out of your topcoat, resulting in flaking, peeling, or a patchy finish.
However, professional painters looking for a high-grade finish will always use a dedicated primer as the first coat on fresh drywall or raw wood. (If the drywall or wood has been painted in the past, dedicated primer is not necessary.)
Poor paint adhesion can manifest in several ways, including cracks, flaking, peeling, and other forms of paint failure. For example, if a wall is not properly cleaned before painting, the paint may fail to adhere and begin peeling within months.
Knowing how to tell if plaster is dry enough to paint is crucial. Dry plaster should be a uniform, pale pink or light grey. If it's darker in patches, it likely still contains moisture. Painting over damp plaster traps moisture, which can eventually cause flaking, bubbling, or blistering on your painted wall.
New plaster is porous, so if you paint it with standard paint it will simply be absorbed by the wall. This means you'll need to apply more coats of paint, and the paint could start to peel later as it dries. To prevent this happening, you need to apply a mist coat first.
Yes, Murphy’s Oil Soap is effective for cleaning walls, particularly for removing dirt and grime on wood paneling, painted surfaces, and baseboards. It works best when diluted with warm water, making it a safe, gentle cleaner, although it is recommended to test a small, hidden area first, especially on flat paint.
The ultimate lazy shower hack is the "Shower and Soak" method. Mix equal parts distilled white vinegar and original blue Dawn dish soap in a soap-dispensing dish brush. Keep it in your shower, and while your hair conditioner sits, give the walls a quick scrub. Rinse as you shower for a perpetually clean bathroom.
Surfaces to avoid with Dawn® Powerwash: Marble countertops, sink basins, and backsplashes. Wood, including unsealed, varnished, stained, or painted wood surfaces & furniture.