A running toilet may not be quite as bad as a clogged toilet, but if left unchecked, this problem can waste hundreds of gallons of water and quite a few dollars.
More often than not, continuously running toilets are extremely easy and inexpensive to fix – you might just need to replace the flapper. A constantly running toilet also presents an increased risk of flooding. This risk can come in a few forms.
A running toilet may just seem like a nuisance, but it can lead to other, more significant problems, like wasting water or causing damage to your home through flooding.
A continuously running toilet can waste up to 200 gallons a day or more depending on the volume flow down the drain. This can cause a terrible increase to a family's typical water use, so fix toilet leaks as soon as possible. Some leaks are easy to find, such as a dripping faucet or running toilet.
If you only notice your toilet running in the middle of the night, there is a good chance that the water level in your tank is set too high.
The average leaky toilet can waste about 200 gallons of water per day. That's over 6,000 gallons a month ($70.06*) for just one leaking toilet! Some toilets may produce a running water sound that is easy to hear. Some leaks are visible as a small trickle running from the rim to the water in the bowl.
Typically, a running water toilet will waste thousands of gallons of water per month which translates to approximately $200 unnecessarily tacked onto your monthly water bill-- that's nearly $2,500 dollars a year down your toilet bowl. The above scenario is in the case of an extreme toilet leak.
More often than not, the flapper valve could need adjustment, or you may need to replace the toilet fill valve. Both are relatively small fixes that most homeowners can usually handle without calling in a professional plumber or having to remove the toilet and then having to install a new one.
Depending on the water pressure to your house, a running toilet can leak over one gallon of water per hour. This is almost one unit of water a month. If left undiscovered, a running toilet can waste almost 13 units of water a year. Fortunately, most toilet leaks are relatively easy to fix.
Depending on the amount of water remaining in the pipes, you might be able to flush your toilet several times while the power is out. Eventually, however, your tank won't fill up anymore because the pumps are down. When this happens, you will need to flush your toilet manually by pouring in a bucket of water.
The steady flow of water from a leaky toilet or faucet day and night can quickly flood your septic tank as well as the ground around the drain field, making it impossible for water to flow out of your septic system, eventually leading to septic system failure. This is referred to as hydraulic overloading.
If you suspect your toilet keeps running because of a major leak or damage to the bowl, gasket, flushing mechanism, or pipes, call a plumber right away. Be wary of easy, DIY solutions that might make problems worse, costing you more time, stress, and money in the long run.
Running toilets can have different speeds at which they cost you money. A slow leak can waste 30 gallons a day while keeping you oblivious to the problem. A medium leak, on the other hand, is more noticeable and will go through roughly 250 gallons and $3.30 a day.
A running toilet can be the result of a variety of factors. Here are the most common causes of a running toilet: Flapper seal failure. Length of the flapper chain. Leaky fill valve.
The first thing you should do when considering replacing your toilet is to look at the age. Most plumbers agree that an average toilet can last around 50 years.
Toilets made from the early 1980s to 1992 typically used 3.5 gallons per flush (13.2 liters) or more. Toilets made prior to 1980 typically used 5.0 to 7.0 or high gallons per flush (18.9 lpf to 26.5 lpf). The oldest toilets can use more than 8 gallons per flush (30 lpf).
If the valve is still filling and the water is up to the line in the bowl, then the amount of water going into the bowl is too high and needs to be adjusted.
So that's 1.5 gallons per flush or per 30 seconds, or 3 gallons per minute. For all 1,440 minutes per day, that is up to 4,320 gallons of wasted water! If you left your leaky toilet running this way for an entire week, you'd waste 30,240 gallons of water.
This kind of sound can occur intermittently or as frequently as every minute and usually means your toilet is losing water. If you are experiencing a running toilet, you may have an internal/external leak or an issue with the flapper.
The most likely cause is capillary action. This happens when a piece of debris, wicks the water out of the bowl and down the drain. It could be something as small as a string. Another possibility is the drain venting in the home is not sized properly, or a clogged vent.
The most common reason for a toilet being slow to fill is due to a partially open water supply valve. Check to make sure the valve is open and letting water flow freely into the tank when it needs to fill. If it's closed or only partially open, open it fully to allow plenty of water to flow.
Once a week at least.
Tetro says your bathroom is the ultimate bacteria host; E. coli can be found within six feet of the toilet and in the sink. To keep it at bay, disinfect the toilet and sink at least once weekly, and the bathtub every two weeks — more if you shower often.