Several gentle pumps will usually work better than a couple of hard pushes. If your clog is going to come out, it should happen in less than 10 minutes. If not, it's time to move on to a snake or call a plumber.
You might want to see if the clog works itself out in time. If you have another toilet you can use, let the clogged one set overnight. The water pressure that builds up in the bowl might actually cause the toilet to unclog itself. After a day's wait, flush the toilet again.
The longer you leave a clog, the more opportunities there are for the clog to get worse. The most water-soluble parts of the clog will dissolve, and the rest will fill in the gaps, making the clog worse. There is also the possibility that human error could come into play.
Then pull up sharply to disturb the clog and loosen it. Continue vigorously pushing and pulling until the water begins to drain. It may take 15 to 20 cycles before the toilet unclogs. Be patient.
You may just be using it incorrectly. Do this: Next time you have a clog, use your plunger like this: Ensure the flange lip is unfolded. Get a good seal on the toilet drain (that is, make sure you're covering the entire drain or you won't have enough pressure to loosen the clog.)
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
We recommend you add a cup of baking soda to your blocked toilet and wait for some minutes. Next, pour two cups of vinegar slowly into the toilet. Vinegar and baking soda will typically react to form bubbles, so ensure you pour carefully and slowly to prevent the toilet water from overflowing or splashing.
When a toilet has a clog made of water-soluble materials, it has a chance of slowly dissolving in the water and freeing up the toilet to work properly again. So, clogs that are primarily made of toilet paper can clear themselves.
You can use dish soap and a bucket of hot water to unclog your clogged toilet. If the toilet clog doesn't go away, you may want to consider repeating the process with a stronger product, like bleach. Chemical drain cleaners should be avoided, or only used as a last resort.
Check water level in toilet bowl
Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
Attempting to force a clog through a toilet with a plunger can often make the problem worse. Instead, create a seal and slowly push down on the plunger before pulling it back sharply. The suction can help pull the clog back up toward the bowl, breaking the blockage and allowing gravity to take over.
You can use Drano® Clog Removers to unclog a kitchen sink, bathroom sink, shower or clogged bathtub, but DO NOT use them in toilets. For clogged or slow-running drains, apply the product and let it work 15 minutes, then flush with hot water.
You're Using Too Much or the Wrong Toilet Paper
They then end up forming solid lumps within the drain lines and clogging them. Solution: Use and flush an appropriate amount of toilet paper.
If your toilet isn't flushing all the way, it's most likely because of one of these problems: The water level in your toilet tank is set too low. Problems with your flapper. A clog in the toilet, flange or drain.
When it comes to simpler clogs, expect to pay no more than $150, while more extensive blockages that require dismantling the toilet's plumbing could cost between $150 and $500. A DIY drain snake costs between $5 and $50, so it may be affordable for homeowners to take the first attempt at unclogging themselves.
It is Extremely Corrosive For Your Drains
When your pipes are clogged, Drano will sit on top of the clog, continually reacting and generating heat until the clog dissolves. This can put a great deal of stress on your drains as the heat can cause PVC pipes to soften and even break or collapse.
Using a snake is also more invasive and time-consuming than using a chemical cleaner is, and can often become a dirty job. When it comes to getting at and removing major clogs or clogs that are deep down in your pipes, however, a plumber's snake is your best bet.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
We recommend you add a cup of baking soda to your blocked toilet and wait for some minutes. Next, pour two cups of vinegar slowly into the toilet. Vinegar and baking soda will typically react to form bubbles, so ensure you pour carefully and slowly to prevent the toilet water from overflowing or splashing.