Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
Water Pressure Readings
Normal water pressure is generally between 40 and 60 PSI. Most homeowners prefer something right in the middle around 50 PSI. Once you measure the water pressure in your house, you can adjust it to a setting that is ideal for all family members and household uses.
Most residential plumbing systems are designed to handle 40 to 60 PSI of pressure, with 80 PSI being the typical maximum and anything over 100 PSI being possibly detrimental to plumbing components.
According to statistics, water pressure above 80 psi (pounds per square inch) causes the failure of water fixtures. The most common signs are spitting or leaking faucets, especially if it's out of the cold tap.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
Consider calling a professional if the water pressure reading goes above 80 psi.
Adjust the Pressure-Reducing Valve
Protruding from the top of the valve is a threaded bolt. To raise pressure, loosen the bolt's locking nut, then turn the bolt clockwise. Use the pressure gauge to determine when you reach a water pressure around 50 PSI. Then, tighten the locknut to secure the valve.
Now, if the gauge shows that the entire house has low water pressure, then try adjusting the pressure-reducing valve. Look on the main supply pipe near your water meter for a conical valve that has a bolt sticking out of the cone. To raise pressure, turn the bolt clockwise after loosening its locknut.
If you're dealing with ongoing high water pressure, you should check on your regulator. You may be able to lower your water pressure by adjusting the regulator, or you might need to replace it with a new one. Older homes may not have been constructed with a water pressure regulator.
Is your water pressure too high? Most plumbing fixtures are designed to handle a maximum water pressure of 80 psi or lower. If your water pressure is higher than that, it can potentially cause the parts for your faucets, water heater, toilets, and shut-off valves to fail.
Shut off the cold water at the faucet behind the washing machine, and then disconnect the hose from the faucet. (Be careful as it will be full of water.) Screw the pressure gauge onto the faucet, and then open the faucet all the way to test the pressure.
Banging or Clanging Noises in Pipes
This is a sign that the pressure in your pipes is already extremely high, and the shuddering is your pipes adapting to the pressure increasing when you turn off the water. This also means that you could find yourself dealing with plumbing leaks within a short period of time.
Residential water pressure tends to range between 45 and 80 psi (pounds per square inch). Anything below 40 psi is considered low and anything below 30 psi is considered too low; the minimum pressure required by most codes is 20 psi. Pressures above 80 psi are too high.
The short answer is low water pressure in your home arises due to a number of causes. Some include a shut or blocked water meter valve, mineral buildup clogs pipes, corroded pipes, or even a crack in the main city supply pipe to your home.
The maximum recommended water pressure for homes is 80 psi; any pressurization exceeding this amount will result in thousands of wasted gallons of water each month.
The primary way to fix high water pressure is by installing a water pressure regulator. If you already have one, you will need to adjust it or replace it.
Water pressure regulator replacement: $250 to $1,000. Pipe section replacement: $500 to $4,000.
Typically, water pressure regulators cost about $50 to $100 on average1, though you could end up paying up to $2001 depending on the size of incoming water line.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
High Pressure
Excessive water pressure can cause stress on your plumbing leading to leaks and burst pipes. If you hear banging from your pipes (known as a water hammer) this is a sure sign of high water pressure. It may mean that the water pressure from your supplier to your house is too high.
Ways to increase water pressure in your shower
Clean your showerhead. Remove the water restrictor. Replace your shower hose. Check if your water shut-off valve is fully open.
Too much water pressure can be dangerous but low water pressure has an equal potential for being dangerous. Low water pressure could also mean that you have a clog somewhere in the system that you need to resolve. You want to do it fast because this can lead to issues with leaks that can cause water damage and mold.
Open your main water valve.
Your house has a main water valve, usually located near the meter; the valve controls the flow of water into your home's pipes. Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure.
The ideal water pressure for a house will be somewhere in the range of about 45 to 65 psi. Anything higher than 80 psi can cause damage, and anything much lower than 45 psi may result in issues when you use your shower, toilet, dishwasher and other water-consuming appliances.