A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
National standard - 2.5 gpm
This includes all type of shower heads like hand-held shower, wall mount shower head, shower head systems, and rain showers. For shower heads made pre 1990s, it is still possible to find 3.5 gpm flow rate or even higher.
For water conservation purposes, most plumbing codes require faucets and showering devices to not exceed a certain maximum flow rate. Removing the flow restrictors could cause these devices to no longer meet these codes.
The average US household can save about 2,900 gallons of water every year simply by installing a single low-flow showerhead. Just one will make that much difference. Multiply that by the number of bathrooms in every house in every town of every state. The impact is overwhelming.
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992.
Also known as "flow rate", GPM is a measure of how many gallons of water flow out of your shower head each minute. Since 1992, a maximum of 2.5 GPM is the federally mandated flow rate for new shower heads. This means no more than 2.5 gallons of water should flow out each minute.
If your showerhead is labeled 2.5 GPM or less, you have a low-flow showerhead. Any showerhead labeled 2.6 GPM or above is a high-flow showerhead. If your showerhead doesn't have a label, try this trick to determine the flow rate. Place a bucket or container with a 1-gallon marker under the showerhead.
Standard shower heads use 2.5 gpm, but to earn the WaterSense label, a product must use no more than 2 gpm and still meet strict performance requirements.
The average bath uses about 80 litres of water. Over the course of four minutes a normal shower head produces about 36 litres.
In applications where a large volume of water is used, such as showers and water filtration systems, a flow restrictor can save you money on your water bill each month. Flow restrictors can be applied to all bathroom and kitchen faucets, and they must be used for reverse osmosis filtration systems.
Two big reasons: To help lower utility bills -- and to conserve water. According to the EPA, the average family could save 2,700 gallons per year by installing WaterSense labeled showerheads. Since these water savings will reduce demands on water heaters, they will also save energy.
Removing a flow restrictor is illegal according to the US Energy Policy Act of 1992, which limits the maximum shower water flow rate to 2.5 gallons per minute (GPM).
Do All New Shower Heads Have Flow Restrictors? Not all new shower heads come with flow restrictors. While many brands focus on water and energy efficiency, it's not a universal feature. So, before you make a purchase, it's a good idea to check the specifications and ensure they fit your needs.
Flow restrictors only allow a set amount of water to flow to the shower head, no matter how much water is flowing through your pipes. If you have low water pressure in your home or building, this can mean even lower pressure in your shower.
A 2.5 gpm shower head will have a better pressure and shower experience than a 1.5 gpm shower head. A 1.8 gpm shower head would have a better pressure and shower experience than a 1.0 gpm shower head. Another drawback of low flow shower heads boosting the pressure is the temperature instability.
A standard showerhead uses 2.5 gallons a minute, or 25 gallons for 10 minutes. Either way, the shower saves water – as long as you don't go past 10 minutes. The shorter the shower, the greater the savings.
Generally, taking a shower uses less water than a full bath. A standard showerhead flows at a rate of 2.5 gallons per minute . This means that a ten-minute shower only uses 25 gallons of water.
A 10-minute shower uses 25 gallons of water (provided you have a standard 2.5 gpm showerhead). In terms of bills, this translates to $0.375 per shower. A ten-minute hot shower uses 6 cents of natural gas, so the total cost comes out to $0.435.
A low-flow shower head with a GPM of 2.0 or less can save the average family 2,700 gallons per year, according to the Environmental Protection Agency (EPA). That's a lot of water savings.
Efficient shower heads use at least 1.5gpm. Taking the same amount of time in the shower uses only 15 gallons of water. The water savings amount up to 65 gallons of water!
Switching to a 2.0 GPM shower head saves more than 1,825 gallons of water and $25 per year in water and energy costs. Those numbers jump to 7,300 gallons and $100 in savings for a family of four. Know the Features. A lower flow rate doesn't have to mean wimpy showers.
A flow rate between 10 and 15 litres per minute is considered acceptable but can be improved. A flow rate that is above 15 litres per minute will be regarded as good.
This is a loaded question, that really comes down to preference and the number of individuals that are in the home. The average household needs 100 to 120 gallons per person per day, and a flow rate of about 6 to 12 gallons per minute.