The average usage of water in a residential sprinkler system is between 12 – 30 gallons per minute depending on the type and size of the sprinkler head.
The standard sprinkler flow rates, in general, are from 4 gallons per minute (gpm) from a 5/32-inch nozzle at 30 pounds pressures to over 11 gpm from a 7/32-inch nozzle at 70 pounds pressures.
The average system uses approximately 15-16 gallons per minute, per station.
Using Direct Measurement of Sprinkler Discharge Rate
Keep track of the time it takes to collect a known volume of water. Then, calculate the sprinkler discharge rate (gallons per minute). Example: If it takes 100 seconds to collect 2 gallons of water from a sprinkler head, the discharge rate is 1.2 gpms.
They report that typical lawn sprinkler irrigation systems may require 12-gallons per minute (gpm) to operate properly. They indicate 10 gpm is the minimum for fire protection, with 20 gpm being preferred.
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992.
Average Water Flow Rate
The water flow rate is the measurement of how fast treated water will come out of your faucets throughout your home. It's measured in gallons per minute (GPM). The average household has a water flow rate of 6 to 12 GPM. Therefore, most households use roughly 100 to 120 gallons of water each day.
A common rule that is followed for obstructions within 18 inches of the sprinkler deflector is the “three times rule”. This requires sprinklers to be positioned away from obstructions a minimum or three times the maximum dimension of the obstruction.
To determine how long you need to water to get one inch, place a plastic container in your yard and set a timer. On average, it will take 30 minutes to get a half inch of water. So, 20 minutes, three times per week will give a lawn about an inch of water. This formula works best with healthy, well-cultivated soil.
Sprinklers generally cover up wider ground and spread out water at a slow yet steady pace, which makes all the soil moisturized evenly and soaked underground. A watering hose takes time to cover space and can clutter the soil if there's too much water.
The answer is that it usually takes up to 30 minutes to get a half inch of water. Watering 3 times per week equals to an inch of water on a lawn. Plants can be watered 1 to 2 times a week in seasons where there is a higher chance of rainfall and less evaporation.
You should run your sprinkler system for as long as it takes to apply a half inch of water to your lawn. You will need to water for at least 10 minutes per week for most systems. Measure your sprinkler system's output to ensure you're not using too much water or underwatering.
However, the flow rate of the Rain Bird PRS spray held steady at 2.1 gallons per minute, saving almost a gallon per minute over the non-PRS spray.
For conventional sprayheads, precipitation rates typically range from 1.3 inches to 2 inches per hour. For gear drive rotors, precipitation rates typically range from 0.4 inch to 1 inch per hour. For rotary nozzles, precipitation rates typically range from 0.4 inch to 0.6 inch per hour.
One inch of water or rain is equivalent to 623 gallons per 1,000 square feet.
Nothing should be in that area between the bottom of the sprinkler heads and the imaginary horizontal plane parallel to the ceiling that is 18 inches below. This is done to allow an even and unobstructed spray pattern from the sprinklers when triggered to extinguish the fire.
At different pressures, the sprinkler head and nozzle will consume different amounts of water. For example, at 35 pounds per square inch (PSI) the 5000 Series Rotor using the 3.0 nozzle will use 3.11 gallons per minute (GPM). If your home's water capacity was 10 GPM, you could place 3 heads per zone.
This is a loaded question, that really comes down to preference and the number of individuals that are in the home. The average household needs 100 to 120 gallons per person per day, and a flow rate of about 6 to 12 gallons per minute.
The typical residential water flow rate for small households is between 6-12 gallons per minute, so unless you plan to add extra kitchens, bathrooms, or laundry rooms to your home in the future, your home will never need to exceed that final GPM, assuming your flow rate is already normal.